Wiring Diagram for Titan BrakeRite EHB Electric-Hydraulic Actuator # T4822500

Question

Question:

titan hydralic brake controller. Model # is 48225. Would you have wiring scematic for this pump.

asked by: Precision A

0

Expert Reply:

I have attached the wiring diagram for the Titan BrakeRite EHB Electric-Hydraulic Actuator # T4822500 that you referenced. This particular actuator is designed for use with hydraulic drum brakes and features 1,000 psi of hydraulic pressure.

I have also attached a short video review that you can check out.

expert reply by: Chris R

0

click to enlarge

Answer 1

On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…

view full answer...

Answer 2

Some trailer brake controllers, including many factory-installed models, will not work with an electric-over-hydraulic type trailer brake actuator like the Hydrastar #HBA16. EOH actuators like this present a very different electrical load to the…

view full answer...

Answer 3

There are a few different diagrams for the Titan BrakeRite EHB Electric-Hydraulic Actuator depending on which model you have. For example, if you have the RF model then you will use the diagram (see photo 1) with a 4-way as that is all that is…

view full answer...

Answer 4

According to Titan, the EHB Adapter, part #T4845900 is NOT necessary with a Titan Brakerite like part #T4813102 if your OE brake controller has an electric over hydraulic mode. If it does, simply switch it to EOH mode. If it only has the electric…

view full answer...

Answer 5

I spoke with my contact at Titan to confirm the operation of the Titan BrakeRite EHB Electric-Hydraulic Actuator for Disc Brakes System, #T4813102, and you are correct that if the BrakeRite is connected to a dead battery, it will bring the system…

view full answer...

Answer 6

It sounds like there may be an issue with the wiring in the trailer to the hydraulic brake actuator. When you installed the Adapter Module #DX35FR you did receive the trailer connected message. I have attached the instructions for the Adapter…

view full answer...

Answer 7

It sounds like that there is something causing a issue with the power coming in from your brake controller (blue wire). To start you will want to verify that you are getting constant 12 volt power using a Multimeter #PT89ZR, to your black wire and…

view full answer...

Answer 8

For your Titan BrakeRite I Plug and Play Electric-Hydraulic Actuator Kit #T4813102 it sounds like you have bled the lines properly, but the power is definitely an issue. It sounds like you have a lack of power from your breakaway to your actuator…

view full answer...

Answer 9

Check the connections of your breakaway system you have on your trailer. It sounds like the plug might be partially pulled or the power from the battery of that system has some how shorted out to the brake output circuit and is telling the actuator…

view full answer...

Answer 10

I would start by verifying that you are getting 12 volt power from your tow vehicle that will charge the batteries on your trailer. If you are not getting power you will need to check charge line on your vehicle with any fuses or circuit breakers…

view full answer...

Answer 11

The issue that you are seeing may indeed be an electrical issue. I recommend checking all the connections and wiring and make sure that there are not any loose connections, or signs of damage to any of the wiring. I have included a link to the…

view full answer...

Answer 12

I would start by checking to make sure that you're getting power on the 12v auxiliary power circuit on your 2003 Chevy Silverado's 7 way plug; since the Titan BrakeRite #T4813102 receives its' power from this circuit…

view full answer...

Wiring Diagram for Titan BrakeRite EHB Electric-Hydraulic Actuator # T4822500

Product Page this Question was Asked From

Continue Researching