What Size Hardware is Needed to Install 55" Lock Side-Door Bar Lock Assembly # 3057-55

Question

Question:

I HAVE A STEALTH TRAILER.... WHAT SIze SECURITY TORX FITS THESE screws

asked by: JOSH

0

Expert Reply:

To install the 55" Lock Side-Door Bar Lock Assembly # 3057-55 you will need to use 5/16 inch fasteners. You will choose the hardware based on the material the assembly will be mounted to. If you used security Torx hardware then you would not necessarily have to bolt the assembly all the way through the surface and secure it with nuts on the other side but I would still recommend it.

expert reply by: Michael H

0

Answer 1

The Optronics Fleet LED Trailer Tail Lights w/ Grommets #TLL12RK has grommets that are 1-1/8 inches deep. The plate dimension if you want to use the integrated lip on the grommet is 3/16 inch and if not is up to 1/2 inch. I went out to our warehouse…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 5

For your bearings, I recommend the etrailer.com Replacement Trailer Hub Bearing #LM67048. For your seals, I can't find the part number or dimensions anywhere, so if you send me dimensions of inside and outside diameters, I'll do what I can to…

view full answer...

Answer 6

For your 2021 Chevrolet Blazer you're going to need to start with a base plate kit. Since there aren't any Blue Ox base plates I'd recommend going with the Roadmaster Direct-Connect Base Plate Kit #RM-523204-5. These are just as good as…

view full answer...

Answer 7

That would depend on several different factors such how much the door sticks out away from the trailer and how much the handle sticks out away from the door. However, if you do run into clearance issues you can always install a spacer on the hinge…

view full answer...

Answer 8

Yes, the Dexter E-Z Flex Equalizer #K71-655-00 will indeed work with the standard 1-3/4" wide double eye leaf springs.

view full answer...

Answer 9

We do offer a few of the 7-3/4" long equalizers with 3 9/16" holes. Unfortunately, the standard equalizers in this size like the #TREQE1 are not greaseable. There is the Dexter E-Z Flex Equalizer #K71-655-00 which is a 7-3/4" long…

view full answer...

Answer 10

I have a great solution for using a weight distribution system with your new V-nose cargo trailer. I recommend using the Reese Chain Hangers #RP58305 with the weight distribution system you choose. These brackets can either be bolted onto or welded…

view full answer...

Answer 11

The closest thing we have to a 2" x 2" bumper is the Rubber Bumper for Enclosed Trailer Ramp Door #37210715 you looked at. This has a 2-1/2" diameter with a height of 1" and a 3/8" mounting hole.

view full answer...

Answer 12

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...