Recommended Wiring Harness and Installation Instructions for 2013 Acura RDX
Question:
how to route wiring harness for 2013 acura rdx with 75784
asked by: Jason L
Helpful Expert Reply:
The Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118569 as well as the other custom wiring harnesses we carry will all install in a similar manner. This custom-fit T-One connector plugs into your Acura RDX's wiring harness, which is located behind the driver's-side interior trim panel in your rear cargo area. Once you've plugged in the tow harness, locate the fuse box under your Acura RDX's hood and insert the provided 20-amp fuse as indicated in the instructions.
The most preferred way to route the wiring is under the side panel into the rear tire storage area. You can store the connecter there when not in use and then pull it out the hatch door when ready for use. This is the most common installation and operation. If you prefer to have the wiring attached to the hitch, you can use a rubber grommet under the cargo storage area to pull the wire through and then use some sealant like # LT37467 to make the wire and cut grommet water tight again. Then you can use mounting bracket # 18144 on your Draw-Tite Hitch # 75784.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Loctite RTV 598 High-Performance Silicone Gasket Maker - Black - 2.7-Fl Oz Tube
- Lubricants Sealants Adhesives
- Sealant
- Gasket Maker
- 2.7 oz
- Loctite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Q&A: Recommended Trailer Hitch for 2013 Acura RDX to use with Bike Rack
- Shop: Trailer Wiring
- Q&A: Do I Still Need to Use the Stabilizer Straps on my Curt Hitch When Carrying a Bike Rack
- Search Results: trailer hitch wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Thule T2 Pro X Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Kuat NV 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Metallic Black
- Shop: Kuat NV 2.0 Bike Rack for 2 Bikes - 1-1/4" Hitches - Wheel Mount - Gunmetal Gray
- Video: Trailer Hitch Installation - 2013 Acura RDX - Curt
- Shop: Roof Rack
- Video: Best 2013 Acura RDX Trailer Wiring Options
- Video: Best 2013 Acura RDX Hitch Options
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Choosing the Right Trailer Wiring
- Search Results: trailer hitch
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: etrailer Class III Trailer Hitch Installation - 2024 Subaru Crosstrek
- Q&A: Recommended Hitch for a 2024 Toyota Grand Highlander
- Shop: Brake Controller
- Article: My Trailer Hitch Doesn't Fit
- Article: Trailer Wiring Diagrams
- Search Results: wiring harness
- Q&A: What is the Difference Between Class 1 and Class 2 Hitches for the Scion XB
on Trailer Hitch
