Weight Capacity of Fulton Drop-Leg Stabilizer Jack # FSJ1-SJ2

Question

Question:

3000 lbs each, 6000 lbs for 2?

asked by: Doug A

1

Helpful Expert Reply:

The Fulton Drop-Leg Stabilizer Jack with Mounting Channel # FSJ1-SJ2 referenced in your question features a 3,000 pound weight capacity for a single leg. Using 2 of the stabilizer jacks would give you a combined capacity of 6,000 pounds like you mentioned.

This jack includes 1 stabilizer so you if you need a pair you will just need to order 2. I have attached a short video demonstration that you can also check out.

expert reply by: Chris R

1

Answer 1

For a pair of rear stabilizer jacks that you can weld directly to the frame of your 2020 Griffin 7 ton dump trailer, I recommend two of the etrailer Square Direct Weld Jack part #TJD-8000S. It measures 25-1/8 inches from the bottom of the foot to top…

view full answer...

Answer 2

We have the perfect solution for you. I'd recommend using the Fulton weld-on drop leg stabilizer jack, part #FSJ1-SJ2. The jack is sold individually, but using two of them would provide 6000 lbs of support which would be plenty, as your trailer…

view full answer...

Answer 3

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...