Will Curt Trailer Hitch # C113753 Fit 2015 Subaru BRZ

Question

Question:

Does this hitch fit a 2015 Subaru BRZ

asked by: Jarret S

0

Expert Reply:

I do have an option for you, however the Curt Trailer HItch Receiver # C11375 that you referenced is designed for the 2014-2016 Scion tC and will not fit your 2015 Subaru BRZ.

For your Subaru I instead recommend the Curt Class I Round Tube Receiver Hitch # C11379. This custom hitch will use existing holes in the vehicle's frame for a no-drill installation. All the needed hardware is included. I have attached the written installation instructions that you can also check out.

If you will be doing some light towing you will also need a wiring harness. For this I recommend the Tekonsha T-One Vehicle Wiring Harness # 118629. This is a custom harness for your Subaru BRZ and it will install by simply plugging into factory ports behind the driver and passenger side tail lights (inside the trunk). After these connections are made you will need to run the hot lead up to the vehicle battery. This will provide you with a 4-Way connector to connect with and power a trailer's basic signal lights.

I have included the installation instructions for this harness as well.

expert reply by: Chris R

0

Answer 1

The Curt hitch part #C11379 that you referenced has been confirmed as a fit for your 2015 Subaru BRZ so it would work well for you. I looked up pictures of your vehicle and the trunk looks like it opens basically straight up so it would not interfere…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...