Troubleshooting Blown Fuse on 2016 Jeep Cherokee North Brake Controller
Question:
Jeep cherokee North 2016 Salut !! J’ai trouver le connecteur pour les freins électrique mais malheureusement le fil blanc et le fil noir ce sont toucher donc je n’est plus de courant !! J’aimerais savoir où est situé la fuse pour cette connection ??? Merci beaucoup Hello !! I find the connector for the electric brakes but unfortunately the white wire and the black wire are touch so I'm not current! I would like to know where is the fuse for this connection ??? thank you very much
asked by: Jean
Expert Reply:
For your 2016 Jeep Cherokee North, the custom wiring harness # 3014-P is the correct fit. The connector is behind the black cover located to the left of the steering column, just above the carpet. To plug in the adapter, first remove the cover. If the black and white wire touched, then you grounded your 12V power and after you correct the wiring, the fuse F42 should be blown (according to the online owners manual on page 725) and will need replacing. You will want to use a circuit tester like # PTW2993 to confirm power and test wiring to make sure you don't have a short if that doesn't solve your power issue or to test your controller if it isn't working properly after this fix.
Pour votre Jeep Cherokee North 2016, le faisceau de câbles personnalisé # 3014-P est la solution idéale. Le connecteur se trouve derrière le capot noir situé à gauche de la colonne de direction, juste au-dessus du tapis. Pour brancher l'adaptateur, retirez d'abord le capot. Si le fil noir et blanc a touché, vous avez mis à la terre votre alimentation 12 V et après avoir corrigé le câblage, le fusible F42 doit être grillé (conformément au manuel de l'utilisateur en ligne à la page 725) et doit être remplacé. Vous voudrez utiliser un testeur de circuit comme # 3808 pour confirmer l'alimentation et tester le câblage pour vous assurer que vous n'avez pas un court si cela ne résout pas votre problème d'alimentation ou de tester votre contrôleur s'il ne fonctionne pas correctement après cela. réparer
Products Referenced in This Question
Product Page this Question was Asked From
Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Replacement Bearings, Races, Seals, and Brakes For a Dexter D35 and D44 Axle
- Q&A: Can a 2023 Dodge Durango Be Flat Towed?
- Q&A: Parts Needed To Install 7-Way & Trailer Brake Controller On 2024 Grand Highlander With Factory 4-Way
- Q&A: Replacement Motor for Kwikee 32 Steps with Power Gear 903209000 Motor
- Q&A: Parts Needed To Flat Tow 2023 Subaru Crosstrek
- Q&A: Troubleshooting the Comp Freeze Error Code on Air Lift Compressor Remote
- Q&A: 2019 Jeep Cherokee Trailhawk Trailer Brake Controller Installation
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: Troubleshooting Brake Controller Installations
- Article: Double-Eye Trailer Suspension System Review
- Article: Using a Portable Generator on RV