Recommended Trailer Hitch and Wiring for 2008 Chevy Uplander
Question:
I will be towing a small trailer with inflatables weighing a total of about 1000 pounds. What is the best hitch for my vehicle?
asked by: Youloundra S
Expert Reply:
For your 2008 Chevy Uplander, I recommend the Draw-Tite Class III Max Frame Receiver Hitch # 75278. This Class III hitch is confirmed to fit your vehicle and has more than enough capacity to pull your 1,000 pound trailer with inflatables. It will provide you with a 2 inch receiver that will work great with a ball mount for towing or other accessories such as a bike rack that you may want to use down the line.
I have attached an installation video on your Uplander that you can use for reference.
In order to tow your trailer you will also need to add a trailer wiring harness. For this I recommend the Tekonsha T-One Vehicle Wiring Harness # 118396. This custom harness will install by simply plugging into factory ports behind the driver and passenger side tail lights. This will provide you with a 4-Way connector that will connect with and power the trailer's basic signal lights.
I have again attached an installation video that you can check out.
Lastly, you will need a ball mount and hitch ball. I have attached a great article that explains how to choose the best one for your setup along with a link that will take you to our available selection.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Trailer Hitch Installation - 2008 Chevrolet Uplander - Draw-Tite
- Shop: Roof Rack
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Article: My Trailer Hitch Doesn't Fit
- Search Results: hitch
- Search Results: tow hitch
- Video: How to Make a Thread Tap
- Video: Cleaning Weld Nuts for Trailer Hitch Installation
- Q&A: Draw-Tite Trailer Hitch for 2008 Chevy Uplander with 113-Inch Wheelbase
- Q&A: How To Determine If 2009 Pontiac Montana SV6 Has Long Or Short Wheel Base
- Q&A: Trailer Hitch and Wiring Recommendation for 2009 Chevy Uplander
- Q&A: Will the Draw-Tite Trailer Hitch Receiver # 75278 Fit a 2008 Chevrolet Uplander LS MiniShort
- Search Results: latch repair kit
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Loctite Blue Stick Threadlocker - Medium Strength - 1/4" to 3/4" Nut/Bolt - 0.32 Oz Stick
- Shop: Loctite Threadlocker 243 - Surface Insensitive - 1/4" to 3/4" Nuts/Bolts -
- Q&A: Troubleshooting Hitch Install Bolts Not Threading Into Frame Rail Weld Nut
- Q&A: What Size Thread Tap Would be Needed for Hitch Install Weld Nuts of 2008 Chevy Equinox
- Search Results: trailer hitch
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: roof rack
- Shop: Suspension Enhancement
on Trailer Hitch
