Height of Uprights of 75" CE Smith Post-Style Guide-Ons

Question

Question:

Hi, I know this product is advertised at 75" tall but what is the actual metal tube height inside the PVC pipe? Thanks,

asked by: Bruce

0

Expert Reply:

The metal tubes inside the CE Smith Post-Style Guide-Ons for Boat Trailers - 75" Tall # CE27636 are the uprights.

These uprights, which are available at part # CE27605PG, measure 39" tall.

expert reply by: Kyle S

0

Answer 1

In regards to the CE Smith Post-Style Guide-Ons for Boat Trailers part #CE27636, if you need to extend the uprights more than 19" from outside of the frame you'd have to replace the horizontal bar stock with a longer option. It's…

view full answer...

Answer 2

The CE Smith Post-Style Guide-Ons for Boat Trailers - 75" Tall #CE27636 has base bars that are 23 inches long to the outside of the bend. The bars adjusts out to 19" from trailer. I've attached a photo to help.

view full answer...

Answer 3

There are a few factors that go into selecting the correct height of boat guide-on. It varies by setup but if you don't know what height you need you can simply go with an option longer than you'll need and then trim as you see fit. The CE…

view full answer...

Answer 4

You are correct in stating that the guideposts on the CE Smith Post-Style Guide-Ons for Boat Trailers - 60" Tall #CE27640 will only adjust out to 13 inches from your trailer. The mounting brackets used will not be able to provide any additional…

view full answer...

Answer 5

The best replacement boat guide-on upright we have for you is the Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers part #CE27605PG which measures 39" tall with a 23" long bottom leg. In order to obtain the exact…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 10

The closest match we have is the part #e54SR which is for a 3,500 lb axle and is 25-1/8 inches long. It would be a bit longer than what you have but it would work.

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...