Does Trailer Hitch for 2014 Audi Q7 Come With Wiring Harness?

Question

Question:

Does this product come with wiring harness?

asked by: Bill A

0

Expert Reply:

The Draw-Tite # 75950 does not come with a wiring harness but there is one available for your 2014 Audi Q7.

For the harness you need part # 119250KIT to add a 4-way, which is going to allow you to power your trailer's lights.

expert reply by: Kyle S

0

Answer 1

I would be happy to help you. We hear this complaint quite often about dealerships not wanting to install after market wiring for random reasons because they want you to purchase theirs usually. The Curt Shock Absorbing Towing Kit w/ Sway Control and…

view full answer...

Answer 2

The Draw-Tite Max-Frame Trailer Hitch Receiver part #75950 is an excellent option for a 2013 Audi Q7. It is rated higher than the factory hitch at 7,500 gross trailer weight and 750 lbs tongue weight. This does not mean you can tow more as the…

view full answer...

Answer 3

When installing the Draw Tite Hitch part #75950 on your 2014 Audi Q7 the backup sensor does get unplugged, but it does not need to be re-calibrated or programmed to work properly. We installed this hitch on a Q7 just like yours and did not have that…

view full answer...

Answer 4

There are some wires that run along the frame rail on your 2014 F-150. I have attached a photo that shows where you can find the wires. They will be on the driver side. I have attached a link to a helpful article on installing a brake controller on a…

view full answer...

Answer 5

On a trailer 7-way the pin in the 1:00 position is the 12 volt accessory circuit that would have 12 volts of power all the time. I am not sure exactly what you mean by #4 but I attached a picture of a 7-way diagram that shows what all of the pins are…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...