Will the Replacement Caster Wheel # UF49-954035 Fit a 1-3/4" Jack Tube

Question

Question:

I just want to verify that this wheel UF49-954035 fits a 1 3/4 inch jack tube.

asked by: Ron E

0

Expert Reply:

Yes, the Replacement Caster Wheel # UF49-954035 that you referenced is compatible with trailer jack inner tubes that measure 1-3/4" in diameter.

This is verified in the attached review video.

expert reply by: Jon G

0

Answer 1

I do have an option for you to replace the bottom plate of your trailer jack with a wheel assembly. The option I have is the Pro Series 6", Detachable Caster w/ Pin for 2" Diameter Jacks - 1,200 lbs #PS1400750340. This corrosion-resistant,…

view full answer...

Answer 2

The vast majority of trailer jack wheels don't use traditional steel ball bearings as they aren't really meant for rotation speed but rather weight bearings. I am not aware of any options which use traditional steel ball bearings. The…

view full answer...

Answer 3

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 4

The closest compatible option for your Dometic DOTR12CB RV microwave's size is the Furrion Standard RV Microwave #FMSN09BL. It measures 19-1/16" W x 13-5/8" H x 15-7/8" D with a 0.9 cu ft capacity.

view full answer...

Answer 5

If your 2016 Honda Pilot Touring has a factory 7-Way connector at the rear of the vehicle, then all you need to install a brake controller like the excellent Tekonsha Prodigy P3 #90195 is the Plug-In Adapter #3070-P. One end of the adapter will plug…

view full answer...

Answer 6

Sounds like you need the Replacement Caster Wheel for Ultra-Fab Manual 2" Trailer Jack #UF49-954035. This is designed to fit both the 2" jack as well as the 1-3/4" tube like what you have. Attached is a review video for you to check…

view full answer...

Answer 7

We have just what you're looking for with the Gen-Y Anti-Rattle Clamp for 2" Hitch Receivers #GY88XR. The sleeve acts as a wedge to take out play between your hitch receiver and extender. Although it does not not require a wrench and a…

view full answer...

Answer 8

Yes, you can install a fifth wheel hitch on a 2021 GMC Sierra 2500 with Carbon Pro Bed. For this, I recommend the Demco Hijacker Autoslide 5th Wheel Trailer Hitch part #DM8550034 with Demco Hijacker Premier Series Above-Bed Base Rails and Custom…

view full answer...

Answer 9

Some jacks do have wheel casters that can replace the foot plate like what you are looking for but there isn't a universal solution that works on all jacks. Instead you'd have to get me the jack brand and model (if you can) and I can see if…

view full answer...

Answer 10

7k Dexter axles are a little annoying as they can have two different seals with only difference being the inner diameter. If the seal has an inner diameter of 2.250 inch you'd want the part #GS-2250DL or if instead you had the spindle diameter as…

view full answer...

Answer 11

The auxiliary 12-volt wire that runs from the 7-way connection to 7-way trailer plug will supply 12-volt power from the vehicle to the trailer. The 12 -volt power will allow interior or exterior lights to run that are not wired in to the…

view full answer...

Will the Replacement Caster Wheel # UF49-954035 Fit a 1-3/4" Jack Tube

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching