Replacement Clamp, Hinge and Tarp Parts for Extang Trifecta Tonneau Cover on 1999 Ford Ranger

Question

Question:

I have the original cover not the 2.0 version, do you have any replacement parts for my 1999 Ford Ranger XLT? I’m looking for the cab clamp assembly EX 1033 tailgate hinges EX 1034 and the vinyl tonneau cover I saw a cover for the EX 43650 only please confirm/correct these model #’s as required. Thank you. 060308-44630 Extang Trifecta Vinyl Tonneau Cover

asked by: It

1

Helpful Expert Reply:

I was able to use the cover part number you provided, 060308-44630, to confirm with my contact at Extang which replacement parts you need.

For the Cab Clamp use part # EX1034; for the Tailgate Hinge use # EX1033; and for the tarp portion use part # EX43630A.

expert reply by: Adam R

1

Answer 1

Yes, we do offer the Replacement Tarp for Extang Trifectia Original part #EX22MR (43461B) which is for a 2014 Toyota Tundra.

view full answer...

Answer 2

The Replacement Tarp #EX92405-20 is for a Extang Trifecta 2.0 Soft Tonneau Cover #EX92405 that fits a 2009 - 2014 Ford F-150 5-1/2 Foot Bed. To properly identify the correct replacement cover you will need to locate the part number on the tonneau.…

view full answer...

Answer 3

I spoke with my contact at Extang a while back about the install of the front clamp for Trifecta Cover part #EX1034 and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp…

view full answer...

Answer 4

When installing the Replacement Cab Clamp Assembly #EX1034 on your Extang Tonneau Cover you will first need to remove the screws from the crossbow/support rail of the cover. This is what will allow you to both remove the existing/damaged cab clamp…

view full answer...

Answer 5

I spoke with my contact at Extang about the install of the front clamp for Trifecta Cover part #EX1034 and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp assembly will then be…

view full answer...

Answer 6

I spoke with my contact at Extang regarding the removal of the existing cab clamp on your Trifecta Tonneau Cover. She stated that on the Trifecta covers, after you have removed the screws that hold the cross member in place, you will then need to…

view full answer...

Answer 7

You certainly can substitute the #EX1035 tail clamps with the #EX1034 cab side clamps for a more snug connection. Extang tells me that doing so is perfectly acceptable, but it will make removing the cover more difficult.

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...