Replacement Tarp for Extang Trifectia Original On 2014 Toyota Tundra 5.5' Bed

Question

Question:

I am looking for a replacement tarp for an Extang Trifecta tonneau cover to fit a 2014 Toyota Tundra CrewMax 57 bed. Extang indicates it is part number 43461B may be EX43461B. Is this available through eTrailer?

asked by: Matt

0

Expert Reply:

Yes, we do offer the Replacement Tarp for Extang Trifectia Original part # EX22MR (43461B) which is for a 2014 Toyota Tundra.

expert reply by: Conner L

0

Answer 1

I was able to use the cover part number you provided, 060308-44630, to confirm with my contact at Extang which replacement parts you need. For the Cab Clamp use part #EX1034; for the Tailgate Hinge use #EX1033; and for the tarp portion use part…

view full answer...

Answer 2

The Replacement Tarp #EX92405-20 is for a Extang Trifecta 2.0 Soft Tonneau Cover #EX92405 that fits a 2009 - 2014 Ford F-150 5-1/2 Foot Bed. To properly identify the correct replacement cover you will need to locate the part number on the tonneau.…

view full answer...

Answer 3

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Replacement Tarp for Extang Trifectia Original On 2014 Toyota Tundra 5.5' Bed

Product Page this Question was Asked From

Continue Researching