Firestone Air Bag Kit Recommendation for 2018 Ford F-150 with 3 inch Lift

Question

Question:

I have a 2018 F150 Platinum that has a 3inch lift. I want to add air bags to the rear but with the 3 extra inches of lift there will be too much gap. Is there a kit available for lifted trucks like mine? Firestone or AirRide?

asked by: Michael B

0

Expert Reply:

We have just what you'd need. For a Firestone Ride Rite kit confirmed as a fit for your 2018 Ford F-150 we have the part # F2582 and then for spacers for your 3 inch lift you'd want the part # F2368 which takes up the gap created by the lift kit that you mentioned.

expert reply by: Jameson C

0

Answer 1

Yes! You can charge your Goal Zero Yeti 1500X Lithium Portable Power Station #GZ64FR from your vehicle using 2 different methods; the Regulated Car Adapter #287-98079 or the Yeti Link Vehicle Integration Kit #GZ43ZR. The difference between the two…

view full answer...

Answer 2

You can get 12' EC8 extension cables #GZ96YR to install the Goal Zero Yeti 1500X Lithium Portable Power Station with Boulder 100 Solar Panel - 120V #GZ27FR in your camper. Adding length to the wire can actually end up giving you a voltage drop…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

Generally speaking, the lube plate will need to cover the skid plate on the 5th wheel hitch. There are some pin boxes out there that will recommend a specific lube plate but most of the times this classification will be from the 5th wheel hitch…

view full answer...

Answer 9

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, you are going to also need the Demco Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 when using the Demco Autoslide 5th Wheel Trailer Hitch w/ Slider #DM8550040 with your Road Armor pin box. For a suspension enhancement I…

view full answer...