Will Curt Trailer Hitch Receiver # C11077 Fit The 2014 Honda CRZ &quotEX Model

Question

Question:

Will this model fit a 2014 Honda CRZ EX Model? The muffler placement is different than a standard CRZ- which is why I am asking..

asked by: Christopher C

0

Expert Reply:

Yes, the Curt Trailer Hitch Receiver # C11077 is confirmed fit for 2014 Honda CR-Z. I verified with my contact at Curt manufacturing that you will have no issues installing # C11077 on the EX model.

There is no drilling required for installation. The access holes may need to be enlarged by drilling, filing, or rotary tool. The exhaust must be temporarily lowered for installation. There is underbody trimming required (not fascia).

The recommend ball mount for this setup is # C45520. The recommended pin and clip is # PC2.

expert reply by: Timothy G

0

Answer 1

According to the instructions for Curt trailer hitch #C11077 you will need to trim the underbody panels to remove the area where plastic clips attach the panel to the frame rails. I have linked the instructions and also included a picture from them…

view full answer...

Answer 2

The Curt Hitch part #C11077 that you referenced has been confirmed to fit your 2015 Honda CR-Z so I would recommend it for you. For a ball mount you would want the #C45520, and then for hitch balls #19256 and #19258.

view full answer...

Answer 3

The issue you are describing is actually not terribly uncommon. Occasionally, a newly installed trailer hitch will come very close or make contact with a vehicle's exhaust system, even when everything is installed properly. We actually have a…

view full answer...

Answer 4

It is difficult to determine what is causing a rattling noise without actually being able to see the vehicle, but I can give you some tips on where to look if you are comfortable crawling under your vehicle to look at the hitch. The alternative would…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...