7-Way Extension for Use with 36 Inch SuperTruss Extension

Question

Question:

7-Wire to 6-Wire Flexo-Coil Kit for Truck Camper set up with Super Hitch & Ready Brute Elite So, I have a Eagle Cap 1165 on a RAM 4500 Chasis Cab. Im setting it up with a ReadyBrute Elite tow bar and need to find a hitch extension to bridge the 3foot gap from the truck hitch to clear the back of the camper and then attach the ReadyBrute? Suggestions? Thanks!

asked by: Todd H

0

Expert Reply:

To extend the 7-Way trailer connector out from the back of your truck to the mount on the SuperTruss extension I recommend # TLW6036 which is 36 inches long. Then you could use the Flexo-Coil kit # RM-146-7 like normal.

expert reply by: Michael H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 10

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 11

You'll need to do some slight measuring to ensure the fit of the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F95FV on your 4WD 2022 Ford F-350 FX4 dually. Just measure from the top of the rear axle to the top of the jounce…

view full answer...

Answer 12

As you have a Lippert Tuning Point pin box the only replacement we have is the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY48GR. This converts your 5th wheel to a gooseneck ball connection so you will need a gooseneck ball in your…

view full answer...