Size of Install Bolts that Come with Curt Hitch 13571

Question

Question:

What are the sizes of the bolts included?

asked by: Justin

0

Expert Reply:

To install the Curt hitch part # 13571 the two bolt sizes needed are M12-1.25x40 and M10-1.25x35 which are included.

If you need new bolts you can order them from us as part # RHK.

expert reply by: Jameson C

0

click to enlarge

Answer 1

If you want to install the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13182 on your 2016 Jeep Grand Cherokee, you will use M14 bolts that are grade 5 as well as compatible flat washers. That is the replacement for what is…

view full answer...

Answer 2

The Kenda 205/75R15 size tie on a galvanized wheel, part #AM32397, has a shipping weight of about 46 pounds. There isn't a lot of shipping materials used so the actual tire and wheel will only be a little less than that.

view full answer...

Answer 3

Trailer wiring harness #C55339 installs in a factory wiring harness located on the driver's side of the back of your 2001 Isuzu Trooper. The factory harness should be attached to a grommet between the rear wheel well and the bumper on the…

view full answer...

Answer 4

According to the install instructions for the Tekonsha 7-way part #TK22113 that fits your 2018 Dodge Durango the blue wire gets routed through the grommet in the floor on the driver side into the rear cargo area and then routed behind side cargo trim…

view full answer...

Answer 5

The blue wire of the 7-way kit part #TK22113 goes to the reverse light circuit of your 2015 Dodge Durango. The good news is that if you trailer does not need a reverse light circuit you don't have to connect this circuit but it's there in…

view full answer...

Answer 6

The correct replacement hardware you are looking for is Replacement Hardware for Curt A Series and Q Series 5th Wheel Hitches #C16125-SK4. This will secure the Replacement Head Unit for Curt Q24 5th Wheel Trailer Hitch - 24,000 lbs #C16545 to the 5th…

view full answer...

Answer 7

The bolts included with the Curt Trailer Hitch Receiver #C13240 referenced in your question are M10-1.25 x 30 inch hex bolts. If you are just needing the replacement hardware for the trailer hitch, you will use part #RHK. Once on the product page,…

view full answer...

Answer 8

I took a look at the instructions for the Tekonsha OEM Replacement Vehicle Wiring Harness part #TK22113 which is a fit for a 2019 Dodge Durango and it states the following: "Beginning underneath vehicle, on drivers side. Route 18 gauge blue wire…

view full answer...

Answer 9

According to my research you'll want to get a titanium-coated drill bit or something of the like to drill a hole in the frame of your trailer for installing the Uni-Lite LED Clearance and Side Marker Light w Grommet #MCL11RKB. If you go to your…

view full answer...

Answer 10

I spoke with my contact at Tekonsha and he informed me that the wire is in the passengers front wheel well behind the fender liner. There is a connector that it is attached to on one side. I attached a drawing diagram that shows you where it is.

view full answer...

Answer 11

If you have a standard 3,500 lb axle and the spindle is about an inch in diameter then the correct inner and outer bearings for you are #L44643 which have a 1" inner diameter exactly. This can be found in the kit #BK1-100. If your spindle is…

view full answer...

Answer 12

According to the install instructions for the Tekonsha 7-way part #TK22113 that fits your 2017 Dodge Durango the blue wire gets routed through the grommet in the floor on the driver side into the rear cargo area and then routed behind side cargo trim…

view full answer...

Size of Install Bolts that Come with Curt Hitch 13571

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching