Where to Connect Red and Blue Wires of TK22113 on 2017 Dodge Durango
Question:
Where do they connect exactly each of them 2017 Dodge Durango gt 12 gauge and 18 gauge blue wires
asked by: Jim
0
Expert Reply:
According to the install instructions for the Tekonsha 7-way part # TK22113 that fits your 2017 Dodge Durango the blue wire gets routed through the grommet in the floor on the driver side into the rear cargo area and then routed behind side cargo trim panels and above head liner where you'll locate a white wire with a yellow stripe which it connects to.
I also attached a couple pictures that show where you'll find the connection point as well.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter - 7 Way Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 7 Round - Blade
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Brake Controller
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV- 2"
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: tk22113
- Search Results: 7 pin mounting bracket
- Video: Draw-Tite Max-Frame Trailer Hitch Installation - 2018 Dodge Durango
- Video: Choosing the Right Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Redarc Tow-Pro Elite Brake Controller - Dash Knob - 2 Braking Modes - 1 to 3 Axles - Proportional
- Shop: Curt Spectrum Trailer Brake Controller - Dash Mounted Knob - 1 to 4 Axles - Proportional
- Shop: Mounting Bracket for 7-Way
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Shop: Curt No-Drill Bracket for 6-Way or 7-Way Round Trailer Connector Mounting Bracket - Long
- Video: Trailer Brake Controller Installation - 2014 Dodge Durango
- Video: Trailer Brake Controller Installation - 2013 Dodge Durango
- Search Results: brake controller
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2018 Dodge Durango
- Shop: Side Window Vents
- Shop: Vehicle Air Mattress
- Shop: Suspension Enhancement
- Search Results: hitch
- Video: Review of Draw-Tite Trailer Hitch Ball Mount - Fixed Ball Mount and 2 Inch Ball - DT49MR
- Video: Tekonsha Brake Controller - Proportional Controller - 90885 Review
- Q&A: Troubleshooting Blown Vehicle Fuses Every Time Trailer is Connected
- Search Results: tekonsha
- Q&A: Trailer Lights are Not Working with 4-Way to 7-Way Adapter Plugged Into 2011 Ford Escape
- Q&A: Wiring 4 Wires on Trailer to 7-Way Connector
- Q&A: Running Light Fuse Keeps Blowing Even with Trailer Running Lights Disconnected
James
4/12/2020
So I had a u haul installer install the Tekonsha tk22113 oem wiring harnesses with the primus iq brake controller and when I plug my 7 way round trailer plug into the vehicle which is a 2017 Dodge Durango gt the lights signals and hazards all work with no issues but when I manually push brake controller it reads n.c . So I drove around a little bit and noticed twice that the gas cap door was open so for the fun of while driving I pushed the gas cap door button and the brakes locked up. Any chance I could get some help? I’m asssuming they tapped into the wrong wires