Where Does Blue Wire Connect On Tekonsha OEM Vehicle Wiring Harness for 2019 Dodge Durango

Question

Question:

Blue wire butt connects to green wire 2019 Dodge Durango

asked by: Mike

0

Expert Reply:

I took a look at the instructions for the Tekonsha OEM Replacement Vehicle Wiring Harness part # TK22113 which is a fit for a 2019 Dodge Durango and it states the following:

"Beginning underneath vehicle, on drivers side. Route 18 gauge blue wire through grommet and into rear cargo area. Route behind side cargo trim panels and up above head liner. Locate white wire with yellow stripe in rear cargo door electrical harness."

Therefore, the blue wire should be run to the white wire with yellow stripe.

expert reply by: Conner L

0

Answer 1

That is a bit confusing as to why Dodge would have the plug installed on your 2015 Durango for the Adapter #TK93VR if your model didn't come with the tow package. Since it didn't come with the tow package you need to hardwire everything.…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

Hi Andrei; yep, you're 100 percent right, you should use the 30 amp breaker. That's why for the installation kit I recommend using the Universal Installation Kit for Trailer Brake Controller #ETBC7. The #ETBC7 comes with multiple breakers,…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 9

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Where Does Blue Wire Connect On Tekonsha OEM Vehicle Wiring Harness for 2019 Dodge Durango

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching