What Comes with K2 Plow Mount Kit # K284219

Question

Question:

K2SUMM8826 K284219 the plow and the mountain kit go together with a crossbar correct ? If I buy these two things everything I need will be there correct ?

asked by: Jonathan S

1

Helpful Expert Reply:

What comes with the Plow Mount part # K284219 that you referenced is what's in the picture I attached.

The crossbar type portion of the plow setup is on the plow side of the setup like with # K2RAMP8219.

expert reply by: Jameson C

1

click to enlarge

Jonathan S.

10/26/2017

K2SUMM8826 K284219 the plow and the mountain kit go together with a crossbar correct ? If I buy these two things everything I need will be there correct ?

Reply

Jameson C.

10/26/2017

Yes, with just those two part numbers you'd have everything you'd need to install and use the plow.

Reply

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 4

The Curt #31604 fits all models of the 1999 Dodge Ram 2500 with the exception of the Sport. As long as your truck is not the Sport model you will be able to install this on the front.

view full answer...

Answer 5

If you already have a front mount hitch then all you'll need is a snowplow which uses the hitch receiver for installation. The Detail K2 Elite Snowplow for 2" Hitches part # K2AVAL8826ELT for example is a great option with an 88" wide…

view full answer...

Answer 6

Yes, the difference between the Detail K2 Snowplow #K2AVAL8422 and Detail K2 Elite Snowplow #K2AVAL8422ELT is the Elite has the electric actuator over the winch. The Elite also uses a chain connection to the blade while the basic K2 has a strap that…

view full answer...

Answer 7

From your recent searches, I believe you are asking about the Detail K2 Elite Snowplow for 2" Hitches - 88" Wide x 26" Tall #K2AVAL8826ELT. This snowplow is confirmed to fit your 2000 Ram 2500 4x4 as long as you do not have the Sport…

view full answer...

Answer 8

I contacted DK2 and they were able to confirm that the Actuator Kit #K2ACT8020 will work to replace the winch on your Summit II Snow Plow. This kit comes with everything you need to install the actuator.

view full answer...

Answer 9

Yes. The Curt Front Mount Trailer Hitch #C31069 does require drilling holes for installation, but this would be the case for any front mounted hitch on the 2018 GMC Sierra 1500 SLT. I've linked the instructions for this hitch to this answer, but…

view full answer...

Answer 10

From my understanding the Z71 version of the 2005 Chevy Silverado 1500 is an LD, or Light Duty, so the correct mounting hardware kit for you is part #K283013. You should be able to verify this by looking at the inside of the door for your pickup. If…

view full answer...

Answer 11

The Replacement Cross Member Plow Attachment for Detail K2 Snowplows #K2CRM3312 is what is used to connect to the custom fit mounting brackets. These brackets are used instead of a front mounted hitch receiver. I pulled the part from our warehouse…

view full answer...