Mounting Hardware Kit for Detail K2 Crossmember Plow Attachment for 2005 Chevy Silverado 1500 Z71

Question

Question:

I’m ordering these brackets for my 05 1500 Silverado z71. Will they fit?

asked by: Ed

0

Expert Reply:

From my understanding the Z71 version of the 2005 Chevy Silverado 1500 is an LD, or Light Duty, so the correct mounting hardware kit for you is part # K283013.

You should be able to verify this by looking at the inside of the door for your pickup. If it has 1500HD then you have the Heavy Duty version and you need mounting hardware kit # K283011, otherwise it's an LD and the part # K283013 is correct.

expert reply by: Jon G

0

Answer 1

If you already have a front mount hitch then all you'll need is a snowplow which uses the hitch receiver for installation. The Detail K2 Elite Snowplow for 2" Hitches part #K2AVAL8826ELT for example is a great option with an…

view full answer...

Answer 2

Yes, the difference between the Detail K2 Snowplow #K2AVAL8422 and Detail K2 Elite Snowplow #K2AVAL8422ELT is the Elite has the electric actuator over the winch. The Elite also uses a chain connection to the blade while the basic K2 has a strap…

view full answer...

Answer 3

Yes. The Curt Front Mount Trailer Hitch #C31069 does require drilling holes for installation, but this would be the case for any front mounted hitch on the 2018 GMC Sierra 1500 SLT. I've linked the instructions for this hitch to this answer,…

view full answer...

Answer 4

I contacted DK2 and they were able to confirm that the Actuator Kit #K2ACT8020 will work to replace the winch on your Summit II Snow Plow. This kit comes with everything you need to install the actuator.

view full answer...

Answer 5

From your recent searches, I believe you are asking about the Detail K2 Elite Snowplow for 2" Hitches - 88" Wide x 26" Tall #K2AVAL8826ELT. This snowplow is confirmed to fit your 2000 Ram 2500 4x4 as long as you do not have the Sport…

view full answer...

Answer 6

The Replacement Cross Member Plow Attachment for Detail K2 Snowplows #K2CRM3312 is what is used to connect to the custom fit mounting brackets. These brackets are used instead of a front mounted hitch receiver. I pulled the part from our warehouse…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 9

I looked up pictures of the taillights that are on the 3110 Featherlite trailers and for the LED version of them you would want the part #STL36RB and #STL37RB. It looks like the spare tire mounts for your trailer are something you would have to get…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Mounting Hardware Kit for Detail K2 Crossmember Plow Attachment for 2005 Chevy Silverado 1500 Z71

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching