Replacement Landing Gear Legs for a 2004 Keystone Montana 5th Wheel Trailer

Question

Question:

I have a 2004 30 Keystone Montana 5th wheel. I need to replace the front Landing legs. I could not find a part # on the legs. But on top of the motor I found a data plate. Lippert Components Inc. Part No. M-9000-PK 12VDC-30 Amp Ignition Protected manufactured by Venture Ser. No. 9000-020193 I dont see that you have a 9000 LB legs. I am assuming that the 9000 on the part number means 9000lb.

asked by: Kent

0

Expert Reply:

The Keystone Montana 5th wheel trailers use special landing gear legs. The lead leg is # LC178653 and the follower is # LC178652. Apparently, these legs have a specific bracket spacing and outer tube height combination that is unique to Montana 5th wheel trailers.

expert reply by: Michael H

0

click to enlarge

Answer 1

The replacement gear box for the Venture landing gear on your 2004 Keystone Sprinter with manufacturer number of VMC940RB - 064625 is part #LC276602. The gear box part #RVLG-RDBOX fits Ram 5th wheel landing gear.

view full answer...

Answer 2

For the Venture landing gear lead leg on your 2004 Keystone Montana you can use repair kit #LC146059. If you ever need the repair kit for the follower leg it is #LC146060.

view full answer...

Answer 3

The overall dimension you are measuring is the length of the outer tube of the jack. If you check out the first picture I attached you'll see where the part #LG-1 measures 29-1/2 inches in length. The second picture I attached shows the…

view full answer...

Answer 4

The difference in the repair kits for your VMC900R will be the Drive Shaft; a lead leg kit will have a different shaped shaft than the follow leg. The replacement Landing Gear Kit for Venture Follow Legs is #LC146060, while the Lead Leg repair kit is…

view full answer...

Answer 5

We may have a replacement lead leg that will work with the landing gear system on your Keystone Sprinter, but I was unable to cross reference the part number you provided to a specific leg that we carry. Most likely the landing gear on your trailer…

view full answer...

Answer 6

The division at Atwood that handled the jacks and landing gear was sold off to Lippert so direct replacement parts are not available. But it is likely that the gear box and motor of another brand will still fit. And yes, the gear box and motor do…

view full answer...

Answer 7

The only follow leg I can recommend you use with your Venture landing gear would be the part #LC179014. Stromberg Carlson makes the Venture landing gear, that is the brands are different but the jacks are the same. I cannot recommend you install a…

view full answer...

Answer 8

The Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs item #LG-142178 you were looking at is the correct replacement motor for the discontinued Atwood 75721. The Gearbox for Venture Electric 5th Wheel RV Landing Gear…

view full answer...

Answer 9

We do have the correct replacement for your Atwood 71119 landing gear motor, which is what is shown in your photo. The replacement part is the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893. I have added a link to a…

view full answer...

Answer 10

Any powered landing gear or powered tongue jack will draw less power as it legs descend down toward the ground and much more as soon as they make contact and encounter resistance. This is a normal occurrence. In the same way, any jack - even a manual…

view full answer...

Answer 11

That sounds like a gear problem. Sounds like the pressure on the bottom of the leg when it is on the ground is keeping the gears lined up properly but once you remove that pressure the gears come apart too far and the jack stops working. Since you…

view full answer...

Answer 12

There are landing gear repair kits for the lead and follower legs on your Keystone Montana 5th wheel trailer. For the lead leg use #LC146059 and for the follower leg use #LC146060. The kits include the gears as well as other parts you may need to…

view full answer...