Replacement Gearbox For Landing Gear On 2004 Keystone Sprinter with Venture VMC940RB-064625

Question

Question:

What part do I need to replace the gearbox in my 2004 Keystone Sprinter 243 FWLRS? The one that is in it is a Venture Mfg Co model # VMC940RB - 064625

asked by: Tyler S

1

Helpful Expert Reply:

The replacement gear box for the Venture landing gear on your 2004 Keystone Sprinter with manufacturer number of VMC940RB - 064625 is part # LC276602. The gear box part # RVLG-RDBOX fits Ram 5th wheel landing gear.

expert reply by: Heather A

1

Answer 1

The Keystone Montana 5th wheel trailers use special landing gear legs. The lead leg is #LC178653 and the follower is #LC178652. Apparently, these legs have a specific bracket spacing and outer tube height combination that is unique to Montana 5th…

view full answer...

Answer 2

We may have a replacement lead leg that will work with the landing gear system on your Keystone Sprinter, but I was unable to cross reference the part number you provided to a specific leg that we carry. Most likely the landing gear on your trailer…

view full answer...

Answer 3

The overall dimension you are measuring is the length of the outer tube of the jack. If you check out the first picture I attached you'll see where the part #LG-1 measures 29-1/2 inches in length. The second picture I attached shows the…

view full answer...

Answer 4

The difference in the repair kits for your VMC900R will be the Drive Shaft; a lead leg kit will have a different shaped shaft than the follow leg. The replacement Landing Gear Kit for Venture Follow Legs is #LC146060, while the Lead Leg repair kit…

view full answer...

Answer 5

The division at Atwood that handled the jacks and landing gear was sold off to Lippert so direct replacement parts are not available. But it is likely that the gear box and motor of another brand will still fit. And yes, the gear box and motor do…

view full answer...

Answer 6

First thing I'd check is make sure the battery on the trailer has a good charge and all of the wiring of the jack and switches are making solid connections. If a powered jack doesn't want to work properly it's very common that…

view full answer...

Answer 7

The only follow leg I can recommend you use with your Venture landing gear would be the part #LC179014. Stromberg Carlson makes the Venture landing gear, that is the brands are different but the jacks are the same. I cannot recommend you install a…

view full answer...

Answer 8

For the Venture landing gear lead leg on your 2004 Keystone Montana you can use repair kit #LC146059. If you ever need the repair kit for the follower leg it is #LC146060.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Replacement Gearbox For Landing Gear On 2004 Keystone Sprinter with Venture VMC940RB-064625

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching