Yakima Roof Rack Components Needed to Install Roof Rack in Pace Tonneau

Question

Question:

I have a Pace Edwards Ultragroove Metal Tonneau cover that has built in rails for mounting a rack. I want to mount a Yakima rack. Id like to know which tower kit and adaptors would be the correct parts for installation?

asked by: Will

0

Expert Reply:

I spoke with my contact at Yakima and he told me that you will need the part numbers # Y00221 (quantity of 2), and part # Y8890027 (quantity 4) for the feet and then crossbars # Y00409 to complete a rack in the Pace rails of your tonneau.

expert reply by: Jameson C

0

Answer 1

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 2

Thank you for the photos! It looks like you have an older Yakima system but we do have the Replacement Yakima Control Tower for Factory-installed Tracks #Y8890027 that will fit. This is sold in a quantity of 1 so be sure to change that to what…

view full answer...

Answer 3

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline…

view full answer...

Answer 4

If you have the Yakima Skyline or Control Towers then you can use the Landing Pad 1 for Yakima SkyLine and Control Towers part #Y00221 to mount them into tracks/channels like those found on select Retrax Tonneau Covers.

view full answer...

Answer 5

The difference between Landing Pad 1 #Y00221 and Landing Pad 4 #Y00224 is the hardware. For LP1 the 'A' plate dimension is 7/8" x 11/16" and for LP4 the 'C' plate dimension is 1 3/16" x…

view full answer...

Answer 6

With the trailer being as light as it is, I don't think you will need a weight distribution system. Typically with a 2017 Ram 1500 pulling this light of a trailer, it can handle the weight without issue. However, if you do end up getting sway…

view full answer...

Answer 7

The B&W Companion Sliding Fifth Wheel Trailer Hitch for Ram Prep Package #BWRVK3670 weighs about 300 pounds when fully assembled. The head, part #BWRVC3006, is about 70 pounds and the base, part #BWRVB3670, is about 230 pounds. By the way, sooner…

view full answer...

Answer 8

Yes. You will need to use everything included with the Rhino-Rack Roof Rack for Thule and Yakima Tracks - 2 Heavy-Duty Crossbars - Black - 65" #Y01-140B-NT to install into the tracks you have pictured. The bases of the legs mount right into the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Yakima Roof Rack Components Needed to Install Roof Rack in Pace Tonneau

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching