What is the Difference Between Yakima Landing Pads 1 and 4

Question

Question:

In looking at the pictures, Landing Pad one looks exactly the same as landing pad 4. In fact Ive seen pics where thd letters LP1 and LP4 are molded into the bottom of the pad. Is there any difference?

asked by: Hans H

0

Expert Reply:

The difference between Landing Pad 1 # Y00221 and Landing Pad 4 # Y00224 is the hardware. For LP1 the 'A' plate dimension is 7/8" x 11/16" and for LP4 the 'C' plate dimension is 1 3/16" x 13/16" so they fit different vehicles.

expert reply by: Michael H

0

Answer 1

We have exactly what you are looking for. The Yakima A Anchor plates #Y8810074 you purchased are designed to work with the Yakima Landing Pad 1 #Y00221 which is not what is in the picture of the landing pads you purchased so you will need to…

view full answer...

Answer 2

It looks like you have the Yakima Landing Pad 1 for Yakima Control Towers #Y00221 on your A.R.E. Canopy, so I recommend using the Skyline Towers for Yakima Crossbars #Y53TR. These towers will allow you to choose between the Jetstream #Y00426…

view full answer...

Answer 3

If you have the Yakima Skyline or Control Towers then you can use the Landing Pad 1 for Yakima SkyLine and Control Towers part #Y00221 to mount them into tracks/channels like those found on select Retrax Tonneau Covers.

view full answer...

Answer 4

The mounting hardware that is needed to install the Landing Pads for Yakima Control Towers part #Y00221 is included therefore no additional purchase will be necessary. I have attached a photo that shows everything that is included in the kit above…

view full answer...

Answer 5

You can use an anti-rattle device such as #SHP2082 as long as the shank on the bike rack is hollow. If it is not hollow then use anti-rattle device #MPG908. I have included a link to a video review of device #MPG908 for you. It is also possible…

view full answer...

Answer 6

I reached out to my contact at Retrax who said that the number you gave me means that you have the RetraxONE MX Hard Tonneau Cover #RT60373 on your 2016 Ford F-150 with the 5-1/2' bed. If your cover is leaking at the tailgate and you have already…

view full answer...

Answer 7

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 8

The T-slot channel dimensions for the Yakima HD Crossbars #Y01158 are 11mm (7/16") wide on top, 8mm(5/16") deep, and 22mm(14/16") wide at it's bottom. I attached a picture of the HD crossbar's diagram as well as a video with…

view full answer...

Answer 9

The Rhino-Rack key and lock systems are not interchangeable with the Yakima SKS lock systems. I noticed you are looking at #Y02-500B which mounts in tracks. The tracks would have to be installed by drilling into the vehicle roof. If you want to avoid…

view full answer...

Answer 10

You'll need an adapter but yes, the Yakima HD crossbars will work with the Retrax Pro XR tonneau cover. What you can use is the following: - Yakima HD Crossbars - 60" Long #Y01157, 68" Long #Y01158, or 78" Long #Y01159 (you'll…

view full answer...

Answer 11

I was able to go out to the warehouse and measure the Yakima Landing Pad 1 for you and found that the mounting hole spacing is 3-15/16 inches from center to center. I have linked a picture and the part to this page for your convenience.

view full answer...

Answer 12

The Yakima Baseline towers #Y28TR with the landing pad 19 will leave you about 5-1/4 inches from the top of your bar to the roof of your 2020 Honda CR-V. That being said the Yakima Showdown #Y04081 will sit about 9 inches up from the top of your bar…

view full answer...

What is the Difference Between Yakima Landing Pads 1 and 4

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching