Recommended Truck Bed Camper Tie Down Kit for 2016 Chevrolet Colorado

Question

Question:

Will the product below fit a 2016 Chevy Colorado? Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4, Item # HSSF

asked by: Angela

0

Expert Reply:

The truck bed camper tie down system we show to be confirmed to work on your 2016 Chevrolet Colorado is the Tork Lift, parts # TLC2221 and # TLC3218, which are the front and rear components.

I contacted Brophy about use of their kit # HSSF. Since this kit is intended for full-size pickups they have not tested it on the Colorado.

The key factors that matter for its fit are that the truck NOT have a drop-in bed liner, plastic bed rails, a double-wall bed nor a side step type bed. Also the underside of the bed rails must provide at least 2-inches of space for the clamp to fit. The external width of the bed rails cannot exceed 5-1/2-inches.

If you refer to the linked video showing installation you will be able to see the vehicle features that will allow installation.

expert reply by: Adam R

0

Answer 1

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 2

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 3

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 11

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 12

The best way to determine the weight capacity of your leaf springs would be to check the weight rating of the axle on your trailer. The trailer will have a plate or sticker on it that will list the VIN number. The weight rating of the axle should be…

view full answer...

Recommended Truck Bed Camper Tie Down Kit for 2016 Chevrolet Colorado

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching