Hitch Receiver and Bike Rack Options to Carry a Pedego Interceptor E-Bike on a 2008 Scion xB

Question

Question:

I am looking for the right trailer hitch to add to my 2008 Scion xB along with a bike trailer for my Pedego Interceptor E-Bike. I doubt I will ever carry more than one e-bike. I need to know the best fit for my vehicle and bike, but also something that will not break the bank!

asked by: Joel H

1

Helpful Expert Reply:

I do have a few different bike rack options for you, but since you are wanting to carry a pretty hefty E-Bike and the highest rated trailer hitch receiver (the Curt # C12490) is only a 1-1/4 inch receiver you do have a very limited range of choices.

Even though the Curt receiver that I recommend, part # C12490, has a max Tongue Weight (TW) of 350 lbs you will want to check that against what the owner's manual says for your 2008 Scion xB and go with whichever weight capacity is lower. Keep in mind that Curt requires the use of a Support Strap # 18050 with all non-trailer loads for their warranty.

Ultimately the best option to carry your E-Bike would be the Thule EasyFold XT 2 Bike Platform Rack # TH903202 it can be used in 1-1/4 or 2 inch receivers and secures bikes by their frame using an adjustable clamp which makes it great for E-Bikes with a step-through frame. This bike rack has a weight limit of 65 lbs per bike. It also comes with bike and bike rack locks to help deter theft of all of your equipment and features a removable ramp to make loading and unloading bikes easier. It is priced fairly high, but you can't beat all of the extra features.

The next step down would be the Kuat NV 2.0 Base # BA12B. This is one of my favorite bike racks because the aluminum frame not only looks sleek, but it can secure up to two 60 lb bikes by their wheels. Unless your bike has a fender it is pretty much guaranteed that your bike will fit. This bike rack also comes with the bike and bike rack locking features.

The most economical option that will fit your 1-1/4 inch receiver is the Yakima HoldUp # Y02445. This has all of the same features as the NV 2.0 Base does (including the 60 lbs per bike weight capacity) but it is made out of steel instead of aluminum. The HoldUp does have a glossy black powder coat finish that is rust resistant, but if there is a scratch on the paint that is not taken care of it will eventually rust unlike the aluminum alternative.

I have attached some review videos of each of the bike racks as well as an installation video of the Curt hitch for you to check out.

expert reply by: Jon G

1

Answer 1

For your 2016 Ford F-150 the best suspension enhancement kit we offer is the RoadActive Suspension Kit part #RAS3611-YHD as it will give you the support you want while dramatically improving stability and ride quality whereas other option will make…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

The correct Roadactive kit that fits your 2023 Ford F-150 is the part #RAS3611-YHD. I really like the RAS kits as they basically don't have any downsides. You get the adjustable support, an easy install, no maintenance, and actually…

view full answer...

Answer 8

Hey Michael, thanks for reaching out! The Timbren Active Off-Road Bumpstops #T28GR you installed on your 2018 Ford F-150 unfortunately have that reputation among users (although Timbren claims their systems provide a smooth ride). Because of this…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 11

Hi Tyler, When adding in air springs on a lifted vehicle the proper way to determine the correct sized spacer is to first install the upper and lower brackets and then measure the distance between them and subtract the height of the air spring…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...