Recommended Trailer Hitch Receiver and Other Parts to Tow a Trailer with a 2014 Audi Q5

Question

Question:

I am looking for hitch for 2014 Audi Q4. I would like to know which hitch Curt #C13136 or Draw-Tite #75940 would provide more ground clearance after installed ? thanks

asked by: Curtis

1

Helpful Expert Reply:

Between the Curt # C13136 and Draw-Tite # 75940 trailer hitch receivers for the 2014 Audi Q5 the Draw-Tite has more ground clearance.

The Draw-Tite installs into the bumper behind a removable piece of fascia that is on the Q5. If this piece of fascia is not on your model then the fascia will need to be cut. The Curt, on the other hand, installs underneath the bumper. So the entire cross beam of the hitch receiver is visible. On the Draw-Tite all you see if the receiver opening and safety chain loops.

I've linked videos of both hitches being installed for you.

If you're going to be towing with your Audi you'll also need trailer wiring. I recommend the Tekonsha # 119250KIT. This will provide you with a 4-way trailer connector to power the trailer's lights.

You'll also need a ball mount and hitch ball. I've attached link of our selection of ball mounts for a 2 inch hitch receiver as well as an article to help you determine the correct rise or drop you may need. Once you choose a ball mount you can then choose a hitch ball to fit it.

One way to make choosing a ball mount easier is to go with an adjustable ball mount like the B&W Tow & Stow # BWTS10038B. It features the ability to be flipped under the hitch when not using it and will provide up to 5-1/2 inches of rise or 5 inches of drop.

For a pin and clip to fit you can use # PC3 or if you'd like to have a locking pin you can use # BX8858.

I've also included links to some articles on towing that you might find helpful.

expert reply by: Charles S

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...