Is The EZ Lube Spindle # TRU74FR Compatible With 10 Inch Brakes

Question

Question:

What size brakes does the flange support? 7 or 10? I am looking for a spindle and brake flange combination that supports 10 brakes. Thanks!

asked by: DT

0

Expert Reply:

I contacted our representative at TruRyde about the EZ Lube Spindle, part # TRU74FR, and he confirmed that it will work for 10 Inch brakes.

I would recommend having a trailer professional install part # TRU74FR, as it requires precision welding. The spindle will need to be welded square and concentric to the axles so the brake will fit and operate properly in the hub.

expert reply by: Reno H

0

Answer 1

Yes, the Dexter axle part #7359765 that you referenced uses the same 84 spindle that you have measures. This will allow you to reuse your current hubs and bearings.

view full answer...

Answer 2

For the Kodiak Disc Brake Assembly - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs #K1HR35D, you need a Dexter #84 Spindle like the #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter #TRU24FR or the #84 E-Z Lube Spindle w/…

view full answer...

Answer 3

In order to determine which replacement axles you need, I will need a few measurements. I will need hub face to hub face measurement, spring center to center dimension, inner and outer wheel bearing reference number, and the axle capacity. Take a…

view full answer...

Answer 4

I spoke with my contact at Redline and he informed me that there is a replacement zerk fitting for your spindle but that it is not the same as one you would see on a tractor or anywhere else. It would be a special order item that we would need to…

view full answer...

Answer 5

Since you have a 2-3/8 inch diameter axle and that indicates you have a 3,500 lb axle the 84 spindle like the part #TRU24FR will work great as that is what capacity this axle was designed for. Installing spindles is a precision job that should only…

view full answer...

Answer 6

Yes, you can use the Dexter Trailer Axle Beam with E-Z Lube Spindles #7359765 as a replacement for what you have. This actually comes with it's own lock washer and nut too so you wouldn't have to try and reuse what you have or source…

view full answer...

Answer 7

The correct replacement axle for a Quality 3500 Lb 95 HF 80 SC is the Dexter Trailer Axle Beam with E-Z Lube Spindles part #7359765. This option will be a direct replacement with no modifications needed. If you want to replace the brakes and…

view full answer...

Answer 8

I have a replacement axle option for you, but we do not have any hubs that will fit your spindle with the #L68149 and LM12749, and I was unable to find any replacements online. The best option is going to be replacing the axle with one that uses…

view full answer...

Answer 9

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be…

view full answer...

Answer 10

Yes, hubs use different size bearings for the inner and outer bearings pretty frequently. The inner bearing will be the bigger size if there are two different size bearings.

view full answer...

Answer 11

TruRyde EZ Lube Spindle #TRU74FR does include a brake mounting flange already welded in place. The linked page displays all of our spindle products which include square-stub spindles without brake flanges like #TRU47FR. We do have 1-3/4-inch…

view full answer...

Answer 12

The TruRyde #84 Spindle #TRU24FR does have a 2 inch diameter, but that is actually designed to fit inside the 2 3/8 inch axle. The stub on the end will extend inside the axle a little ways allowing for added support

view full answer...

Is The EZ Lube Spindle # TRU74FR Compatible With 10 Inch Brakes

Product Page this Question was Asked From

Continue Researching