Recommended Trailer Hitch Receiver For 2010 Mazda 3

Question

Question:

I need to buy a hitch for a Mazda 3 2010 if they have it thanks

asked by: Javier P

0

Expert Reply:

There are specific fits for a 2010 Mazda 3 for the hatchback vs. the sedan. If you have a sedan, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11393. If you have a hatchback, I recommend the Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 24843.

If you will be using this hitch for light towing, I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118420 if you DO NOT have LED lights, and if you DO have LED lights I recommend the 4 Pole Harness and Hardwire Kit - Includes Tester # C59496.

For a ball mount, I recommend the Sportframe Drawbar 4" Rise 2000 lb Kit # 3594. for the Draw tite hitch, or the C45521 for the Curt hitch. Then you will need a hitch ball like # 19256 for a 1-7/8 inch ball or # 19258 for a 2 inch ball.

If you will be using a bike rack or cargo carrier, and you get the Curt hitch, you will also need the stabilization strap like # 18050.

expert reply by: Jason S

0

Answer 1

We have everything you are looking for, but I must warn you that Mazda does not recommend towing with this vehicle, so you would be doing so at your own risk. The other complication is that there is no stated towing capacity for your vehicle because…

view full answer...

Answer 2

For mounting a basket on your crossbars you will need to use the Yakima SkinnyWarrior #Y07014 as the Yakima GearWarrior Cargo Carrier #Y37VR can only be mounted to the Yakima EXO SwingBase #Y34VR or TopShelf #Y94VR. The Yakima SkinnyWarrior #Y07014…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The shortest gooseneck ball we have for the 2024 Chevy puck system is the Reese Elite Series Pop-In Ball #RP23FR. This is going to be very similar to the Curt ball you mentioned. I have included some dimensions of the Reese ball below. From the top…

view full answer...

Recommended Trailer Hitch Receiver For 2010 Mazda 3

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching