What Size Bolts Attach Trailer Hitch to Weld Nuts of 2017 Chevy Equinox

Question

Question:

What is the thread size Metric or english on the weld nuts on the frame where the four bolts go?

asked by: Hunter J

0

Expert Reply:

The bolts that secure the hitch part # e98865 to the weld nuts of your 2017 Chevy Equinox are size M12-1.75 x 40mm.

expert reply by: Jameson C

0

Answer 1

There are a few different size bolts used to attach a trailer hitch to your 2015 Chevrolet Equinox. In order to make sure you get the correct ones, I would need to know exactly what trailer hitch you have as some do use different lengths for this…

view full answer...

Answer 2

The Draw Tite hitch part #76028 that you referenced comes with all of the needed hardware/bolts so you won't need to provide that to complete the install. But since you asked the bolt sizes are 1/2-13 x 1 3/4 (quantity 2), and M12-1.75 x…

view full answer...

Answer 3

The etrailer Trailer Hitch Receiver #e98865 that you referenced is confirmed to fit your 2014 Chevy Equinox. What you are experiencing is not too uncommon and it sounds like you may have already looked into the cause. On vehicles that have seen a…

view full answer...

Answer 4

I wish I had something custom fit I could recommend for you, but none of our hitches that we carry would fit your vehicle as-is. Your best option would be a multi-fit hitch like the part #13703 that would work well for you as long as your frame is…

view full answer...

Answer 5

Depending on the dimensions of your trailer's bumper I believe we could have a solution for you that would not require welding. If you have a 4 inch by 4 inch bumper you could use the part #E-100. If you have 2x4 inch bumper you could use the…

view full answer...

Answer 6

The brackets on the 24x84 etrailer Cargo Carrier for RV Bumper part #e96ZR are not movable. That said, what you can do is slide the carrier left to right which would allow you to make room for a trailer hitch if present. Therefore, the carrier may…

view full answer...

Answer 7

The best priced wheel and tire combo we carry with a 5 on 4-1/2 inch lug pattern, has a ST175/80R13 tire mounted to it, and the rim is made of galvanized steel would be the part #AM31952. I attached a review video to the right for this part number as…

view full answer...

Answer 8

Thank you for the photo; from that it looks like you have a 4-point hinge (like in the accompanying photo I added) and we do have a cover, the Vent Cover for Jensen Trailer Roof Vents - White #61628 which may work for you. If you have an older vent…

view full answer...

Answer 9

Trailer wheel lug nuts that are 1/2-inch inside diameter typically have a 20-TPI thread pitch (20 threads per inch). Most lug nuts also use a 60-degree-coned profile like #CE11051, but a 90-degree like #STN569 is also available for 9/16-inch studs.…

view full answer...

Answer 10

You can wire a license plate light like part #LPL55CB without running wiring up to the front of the trailer. You simply attach the white wire with the ring terminal to a clean, bare metal surface like the trailer frame, and then attach the black wire…

view full answer...

Answer 11

The Yakima FullBack 2 Bike Rack #Y02634 doesn't have any specific instructions for your 2013 Hyundai Tucson. It appears you simply need to uninstall the lower hooks first and with some slack in the hooks you will remove in the same way they were…

view full answer...

Answer 12

Most likely we have what you are looking for but you will need to first determine what vent style you have on your trailer. In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly…

view full answer...

What Size Bolts Attach Trailer Hitch to Weld Nuts of 2017 Chevy Equinox

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching