What Size Bolts are Used to Install Draw Tite Trailer Hitch on 2006 Chevy Equinox

Question

Question:

Can you please tell me what size bolts do I need for this hitch I have a 06 Equinox

asked by: Andy

1

Helpful Expert Reply:

The Draw Tite hitch part # 76028 that you referenced comes with all of the needed hardware/bolts so you won't need to provide that to complete the install. But since you asked the bolt sizes are 1/2-13 x 1 3/4 (quantity 2), and M12-1.75 x 40mm (quantity 6).

I attached a link to an install video for this hitch for you to check out.

expert reply by: Jameson C

1

Answer 1

There are a few different size bolts used to attach a trailer hitch to your 2015 Chevrolet Equinox. In order to make sure you get the correct ones, I would need to know exactly what trailer hitch you have as some do use different lengths for this…

view full answer...

Answer 2

The bolts that secure the hitch part #e98865 to the weld nuts of your 2017 Chevy Equinox are size M12-1.75 x 40mm.

view full answer...

Answer 3

The part number you need to get new installation hardware for the hitch you have for your 2000 Jeep Cherokee is #RHK. On the product page you will need to select the hitch manufacturer, enter the part number for the hitch and then hit add to cart.

view full answer...

Answer 4

The etrailer Trailer Hitch Receiver #e98865 that you referenced is confirmed to fit your 2014 Chevy Equinox. What you are experiencing is not too uncommon and it sounds like you may have already looked into the cause. On vehicles that have seen a few…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 8

Yes, your 2017 Chevrolet Equinox FWD can be flat towed with all 4 wheels on the ground. Do understand that you will need to run your Equinox for 5 minutes every time you stop for gas to properly lubricate your transmission and before towing. A better…

view full answer...

Answer 9

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 10

When the brake pedal is depressed it will send out 12v power through the brake light switch wire to the Tuson DirecLink Base Model Trailer Brake Controller #335DL-100, telling it to activate the brakes on the trailer.

view full answer...

Answer 11

There are two options for a wiring harness for your 2020 Chevy Equinox depending on what model you have. If you have LED tail lights you will want the Roadmaster Smart Diode 7-Wire to 6-Wire Wiring Kit for Variable Voltage LED Tail Lights item…

view full answer...

Answer 12

The Tuson DirecLink Base Model Trailer Brake Controller part #335DL-100 and Tuson DirecLink Lite Trailer Brake Controller part #335DL-50 are both great brake controller options. The best option for you will be dependent on where you will be doing…

view full answer...

What Size Bolts are Used to Install Draw Tite Trailer Hitch on 2006 Chevy Equinox

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching