Is there a Specific Size Weld Needed to Install Tie Down # J-705 to Reach the Maximum Capacity

Question

Question:

What size weld is needed on this to assure that the full capacity of this will be attained?

asked by: Jo

0

Expert Reply:

The short answer is as big of a weld as you can get. There isn't a specified weld size for tie down # J-705 but you will have to weld the whole bracket to the surface it will be attached to. Since it has such a high rating it is possible that the tie down itself will have a higher capacity than what it is welded to. So you may have to reinforce the area with additional steel.

expert reply by: Michael H

0

Answer 1

The only 1/2" to 5/8" chain binders we offer have two hooks, the 13,000 lb-rated Titan Chain Ratchet Type Load Binder for 1/2" - 5/8" Thick Chain #TCRB13 and the 18,100 lb-rated Durabilt Ratchet Chain Binder for…

view full answer...

Answer 2

The internal dimensions of the Curt Heavy Duty D-Ring Tie-Down Anchor #C83760 are 3" wide x 2-1/2" tall as you can see from the attached photo. The working load limit is 8,833 lbs.

view full answer...

Answer 3

That's a good question, because working load limits (WLL) can be somewhat confusing, but I can explain it for you. The 9,200 lb WLL of the Titan Chain Ratcheting Load Binder for 3/8" - 1/2" Thick Chain #TCRB10 simply means…

view full answer...

Answer 4

You might be able to use wheel bolts like #RG02-020 for a set of 4 which are fine threaded. Wheel bolts are used instead of lug nuts for hubs that have thread holes in them rather than the studs sticking out.

view full answer...

Answer 5

The only differences between the Demco Trailer Coupler #DM14976-52 and #DM88XR are the colors and the mounting bracket design. The part DM14976-52 is silver and has a straight, or no-drop, design with the bottom of the coupler being towards the top…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The duty cycle on the Firestone Heavy Duty Air Compressor part #F9499 is 30%. The flow rate of this compressor is 0-30 psi in 14 seconds and 0-60 psi in 35 seconds while using a 1/2 gallon tank. The duty cycle on the Firestone Xtreme-Duty Air…

view full answer...

Answer 8

The wiring that feeds the 12-volt accessory circuit on the 7-way trailer connector is of insufficient gauge to allow enough power to pass through to run a trailer mounted winch. The main function of that circuit would be for lighter-duty…

view full answer...

Answer 9

The Dutton-Lainson Hand Winch w/ Automatic Brake #DL15761 has a nut on the crank handle shaft that prevents it from coming off the winch. As you turn the handle in reverse it will look like the handle is moving away from the main body of the winch…

view full answer...

Answer 10

The correct replacement for an Atwood Water Heater GC6AA-9E is the Dometic RV Water Heater part #DMC74FR. This is a 6 gallon water heater that works with both gas and electric just like the one you have so it will be an exact match.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...