Is there an Adapter to Fit a Hitch Ball with 1 Inch Diameter Shank in a 1-1/4 Ball Hole

Question

Question:

I have a weight distributing hitch with a 1 1/4 hole and a 2 5/16 ball with a 1inch shank. Is there a spacer/adapter available to convert or do I have to buy a new ball?

asked by: James E

0

Expert Reply:

All you will need is a mushing # 58184 that will allow you to use the 1 inch ball shank in the 1-1/4 inch diameter hole on your weight distribution head.

If you instead decide to get a new ball you can use # 19286.

expert reply by: Michael H

0

Answer 1

Yes, we do have replacement hardware for your Curt Trailer Hitch Receiver item #C12091. It is the Replacement Hardware Kit for Trailer Hitches item #RHK. You will want to go to that product page and on the right side you will want to put in Curt…

view full answer...

Answer 2

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball…

view full answer...

Answer 3

Before deciding on a trailer to tow with your 2014 Ford Fusion, knowing the towing limitations of your vehicle will be an important factor. In the owner's manual for the 2014 Fusion, it lists the maximum trailer weight of all the powertrain…

view full answer...

Answer 4

I cannot recommend that you tow a 1,100 lb trailer with your 2016 Ford Fusion SE that has a maximum towing capacity of 1,000 lbs for liability reasons but in all honesty, you would most likely be just fine. Personally, I wouldn't really be…

view full answer...

Answer 5

Yes, you can use the interchangeable ball set #105TB in a 1-1/4 inch ball hole by using a bushing such as #58184 or #F-2.

view full answer...

Answer 6

If you're asking whether or not a 2" Reese ball mount can be used with the Curt Trailer Hitch Receiver #C12115, then the answer is no because this hitch only has an 1 1/4" receiver. Without swapping the hitch out with a 2" hitch…

view full answer...

Answer 7

For your 2024 Toyota Sienna Platinum you will need a 7-way connection along with the brake controller itself. I recommend the following: -Curt Powered Tail Light Converter #C59236 -Universal Installation Kit for Trailer Brake Controller #ETBC7…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

There is not because the only trailer hitch receiver that fits your 2006 Lexus IS 250 is indeed the Class 1, 1-1/4 inch hitch from Curt. I'll go ahead and list below the hitch, and all other parts you'll need for towing if that's what you…

view full answer...

Answer 11

According to the owner's manual, the 2013 Ford C-Max is capable of being flat towed but you'll want to follow the procedures outlined in the owner's manual. For base plates, I'd recommend the #524432-1 from Roadmaster, for a tow bar,…

view full answer...

Answer 12

In order to use the PullRite SuperGlide 20K 2900 5th Wheel Hitch on a 2020 Ford F-250 with factory puck system you can use the Demco 5th Wheel Rail Adapter part #DM6175 which adds 2" to the truck bed or the Reese 5th Wheel Rail Adapter part…

view full answer...

Is there an Adapter to Fit a Hitch Ball with 1 Inch Diameter Shank in a 1-1/4 Ball Hole

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching