Can Interchangeable Ball Set with 1 Inch Diameter Shank be Used in 1-1/4 Inch Ball Hole

Question

Question:

Can this ball set be used with a 1inch bushing in a ball mount that has a 1-1/4inch hole? Thank you

asked by: Jeff

0

Expert Reply:

Yes, you can use the interchangeable ball set # 105TB in a 1-1/4 inch ball hole by using a bushing such as # 58184 or # F-2.

expert reply by: Michael H

0

Answer 1

According to my Convert-a-ball representative, the #AMSC2 and #AMSC2HD both use the same cushion, so there won't be any difference in the cushioning ability of either ball mount. Since you have a trailer ball with a 1 inch diameter shank,…

view full answer...

Answer 2

The Curt RockerBall Shock Absorbing part #C40047 only comes in a 2" ball at this time. You may consider using a ball mount like part #AMSC2HD that has a shock absorbing core with a 2-5/16" ball. The ball hole diameter is 1-1/4". If you…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 9

The shortest gooseneck ball we have for the 2024 Chevy puck system is the Reese Elite Series Pop-In Ball #RP23FR. This is going to be very similar to the Curt ball you mentioned. I have included some dimensions of the Reese ball below. From the top…

view full answer...

Answer 10

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 11

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Can Interchangeable Ball Set with 1 Inch Diameter Shank be Used in 1-1/4 Inch Ball Hole

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching