Using Uni-Servo Wheel Cylinder for 3/16 Inch Brake Assemblies with 1/4 Inch Brake Lines

Question

Question:

What size brake line is the cylinder 3/16 or 1/4?

asked by: Tom M

0

Expert Reply:

The Uni-Servo Wheel Cylinder for 10", 12" and 13" Titan Brake Assemblies # T0977600 fits 3/16 inch brake lines. If you have 1/4 inch brake lines you can use a step-down adapter # HS641-3307 with it.

expert reply by: Charles S

0

Answer 1

For your 1998 Stratos 201, the Westlake ST205/75R15 Radial Tire w 15" Lynx Aluminum Wheel - 5 on 4-1/2 - LR D - Silver #LHAW320 you asked about are a great fit for your trailer and will not have any issues with the weight. Each tire/wheel is…

view full answer...

Answer 2

The thread size that the brake line fittings of the Hydraulic Brake Kit #AKFBBRK-35-D that you referenced is 3/8"-24. This is the standard size that brake lines and fittings are made for.

view full answer...

Answer 3

I spoke to the manufacturer about the Replacement Center Cap part #CXF106B. They informed me that the top removable cap is made of plastic and the cylindrical body that is left on the wheel is made of metal. The retaining ring on the cap is also…

view full answer...

Answer 4

There are several brake lines in varying lengths and sizes between your disc brake assembly and the surge brake coupler on your trailer. I am not sure which one you are looking for but if you can pinpoint this for me I may have some better advice for…

view full answer...

Answer 5

For a replacement brake line I recommend the Titan Hydraulic Brake Line with Fittings #T0776500. This brake line is 18-25/32" long, has a male and female end, and has 3/8"-24 UNF fittings. The thread size on 3/16" fittings is…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Using Uni-Servo Wheel Cylinder for 3/16 Inch Brake Assemblies with 1/4 Inch Brake Lines

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching