Wiring Configuration for Tekonsha Prodigy P3 Trailer Brake Controller 90195
Question:
Hello, I have a question about the Tekonsha Prodigy P3 Electronic Brake Controller. I wanted to confirm that the expected definitions are as follows: 12V Power: 12VDC input Stop light: Signal indicating braking. It is either 0V or 12V. Its an input Ground: Chassis Ground Trailer Brakes: The output voltage signal that is proportional to how hard the brakes is applied. This is the signal we would feed to the trailer to control the brake pump.
asked by: Quincy H
Helpful Expert Reply:
The Prodigy P3 trailer brake controller uses a 4-wire hookup. The white wire is to be grounded to the battery negative terminal; the black power wire connects to the battery hot terminal through a circuit breaker; the red wire takes in the brake light signal from the cold side of the brake light switch and is used to trigger the P3 to send out a brake signal on the blue wire.
The red wire will carry an on-or-off signal; the actual degree of braking power sent to the trailer connector on the blue output wire depends on the power setting and the degree of deceleration in the tow vehicle. Proportional brake controllers like the Prodigy P3 generate their output signal in proportion to the rate the tow vehicle slows down, which keep the vehicle and trailer more in sync with each other for less of the tug-of-war feeling between truck and trailer.
To use the P3 with an electric-over-hydraulic (EOH) brake actuator on the trailer be sure to select EOH mode from the menu screen.
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Article: Brake Controller Installation: Starting from Scratch
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Shop: Trailer Hitch
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Shop: Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Article: Trailer Wiring Diagrams
- Shop: Gooseneck Hitch
- Search Results: tekonsha p3
- Article: Finding the Right Electric Winch
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Redarc Tow-Pro Elite Brake Controller - Dash Knob - 2 Braking Modes - 1 to 3 Axles - Proportional
- Shop: Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers
- Shop: Karrier ST175/80R13 Radial Trailer Tire with 13" White Wheel - 5 on 4-1/2 - Load Range C
- Search Results: hydrastar actuator
- Q&A: Wire Color Coding of Bargman 7-Way Super Sealed Vehicle Side Trailer Connector
- Search Results: puck system
- Search Results: 30180
- Q&A: Recommended Gooseneck Hitch Ball Kit for 2020 Ford F-350 with Factory Puck System
- Video: Draw-Tite Electric Trailer Brake Controller Wiring Kit Review
- Search Results: air bags
- Search Results: brake controller
- Search Results: wiring
- Video: Ultra-Fab Protective Cover for Electric A-Frame Jacks Review
- Article: Testing Trailer Brake Magnets for Proper Function
- Q&A: Installing Prodigy P3 Brake Controller on 2011 GMC Sierra
- Shop: Vehicle Tow Bar Wiring
Robrt
6/27/2020
DoEs a 2016 Hilux have a plug in port for a Tekonsha P3?