Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors

Question

Question:

wiring pollak j560jun93 to 7pin round narva truck to trailer thank.

asked by: Michael

0

Expert Reply:

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, # PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, # PK11720, is pictured also.

expert reply by: Robert G

0

click to enlarge

Answer 1

I attached a diagram that shows how most 7-way rounds like the #PK11720 that you referenced will get wired up. As long as you got yours wired up correctly and your trailer taillights and brakes are functioning correctly that&#39;s all that…

view full answer...

Answer 2

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 3

I attached a picture that shows the pin out diagram for the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole #PK11893-11932 that you referenced.

view full answer...

Answer 4

The wiring color codes and wire gauge recommendations for the Pollak Heavy-Duty, 7-Pole, Round Pin, Trailer Wiring Connector, item #PK11700, are listed below. White - Ground Return - 8 gauge Black - Clearance, Side Marker, Identification - 12 gauge…

view full answer...

Answer 5

I assume this is a replacement axle, so in order to choose the correct one, you will need to know the dimensions of your current axle&#39;s hub-face to hub-face and spring center to spring center as in the diagram I have added, with A being…

view full answer...

Answer 6

On a 7 pin round which is the common connection on a semi trailer, the clearance/marker lights are at the 10 o clock position when you look at the trailer wiring connection. When looking at the connector on the back of the truck, that will put the…

view full answer...

Answer 7

The B and W Flat Bed Fifth Wheel Hitch part #BWRVK3050 will set 10-1/2 inches above the deck height of the flat bed truck it is installed in. I attached a review video for this hitch for you to check out as well.

view full answer...

Answer 8

The Buyers Products Fabricators Hitch Plates like part #3371809042 are not given a weight capacity by the manufacturer. This is because the weight capacity will largely be dependent on how securely it is mounted. The highest rated pintle hook we…

view full answer...

Answer 9

The toe-in adjustment steps for the #DM9713045 are as follows: 1. Put a mark on each side of the locking clamp on the tie rod. 2. Loosen the locking nuts on each end of the tie rod and then the four bolts on the tie rod locking clamp. 3. Turn the…

view full answer...

Answer 10

The king pin dimensions can be the same between fifth wheel trailers and large commercial trailers. Both types of trailers often use a standard 2 inch king pin although semis sometimes have a 3-1/2 inch. As long as your truck fits a 2 inch king pin…

view full answer...

Answer 11

Replacement Base for B&W Companion 5th Wheel Trailer Hitch #BWRVB3500 weighs approximately 131 pounds. Its footprint (overall length and width) is 36 inches by 30-1/2 inches. The measurement from the center of the post where it mounts to…

view full answer...

Answer 12

On the back of the Pollak 7-Pole, Round Pin Trailer Wiring Socket - Vehicle End, part #PK11720, it is marked alongside the pin with the color of the wire that connects to that pin location. I am also including a photo that will show a 7-Way round…

view full answer...

Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching