Replacement Bolts to Secure Thule T2 Bike Rack Classic 2 Bike Extension

Question

Question:

Hi, I have a thule T2 classic with the 4 bike extension. I have misplaced the two bolts that hold the extension on...I think they are 12 mm hitch bolt- do you sell these spares? Thanks!

asked by: Julie

0

Expert Reply:

For the replacement bolts to secure the 2 bike extension part # TH9046 to your # TH9044 you would need the part # 908-1240-54. I confirmed this with Thule. This would be the same if you need to replace the same bolt for the combo #TH9044-TH9046.

expert reply by: Jameson C

0

Answer 1

If you do indeed have the Thule Parkway then the part number you mentioned, #7520990001, is correct. If you would like the locking pin use #THSTL2 instead.

view full answer...

Answer 2

The replacement bolts you need are the Replacement 12 x 40 mm Hitch Bolt for Thule Hitch Bike Racks and Goalpost Hitch Mounted Load Bar, part #908-1240-54. These are the bolts that connect your T2 Classic Add-On to the backbone of your T2 Classic. I…

view full answer...

Answer 3

I checked with Thule for you to verify the correct replacement 12 x 40 mm hex bolt for the Thule Camber bike rack, which is the one you mentioned: - Replacement 12 x 40 mm Hitch Bolt #908-1240-54 This is the right replacement bolt for both the Thule…

view full answer...

Answer 4

The Thule Camber 4 Bike Rack like part #TH9056 uses a hitch bolt, the Replacemnt Hitch Bolt part #853-5917 or the Replacement Locking Hitch Bolt part #THSTL2 which are both 1/2" diameter.

view full answer...

Answer 5

I went to our warehouse to pull this hex head bolt #908-1240-54. This bolt will have a property class of 8.8 and is classified as a high strength steel bolt. The point at which a bolt fails is the tensile strength, and because it is elongated (much…

view full answer...

Answer 6

The correct replacement hitch bolt for the Thule T2 Classic 2 Bike Platform Rack part #TH9045 is part #THSTL2 for locking.

view full answer...

Answer 7

The Thule T2 Pro XTR Bike Rack, part #TH96TX weighs 52 pounds when used as a 2 bike carrier, and can carry up to 2 bikes of up to 60 pounds each. It weighs 96 pounds when used as a 4 bike carrier and can hold up to 160 pounds total with a per-bike…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Replacement Bolts to Secure Thule T2 Bike Rack Classic 2 Bike Extension

Product Page this Question was Asked From

Continue Researching