Replacement Hex Bolt for Thule Camber Bike Rack

Question

Question:

Hi, I have a Thule Camber 4 bike rack and need a new Hex bolt for the hitch. My screw has HY 8.8 on the top and seems to be around 12x40mm. Is this the right one? 908-1240-54 Thank you!

asked by: Jim M

0

Expert Reply:

I checked with Thule for you to verify the correct replacement 12 x 40 mm hex bolt for the Thule Camber bike rack, which is the one you mentioned:

- Replacement 12 x 40 mm Hitch Bolt # 908-1240-54

This is the right replacement bolt for both the Thule Camber 4-Bike Rack # TH9056 and Thule Camber 2-Bike Rack # TH9058.

expert reply by: Kyle S

0

Answer 1

The Thule Camber 4 Bike Rack like part #TH9056 uses a hitch bolt, the Replacemnt Hitch Bolt part #853-5917 or the Replacement Locking Hitch Bolt part #THSTL2 which are both 1/2" diameter.

view full answer...

Answer 2

For the replacement bolts to secure the 2 bike extension part #TH9046 to your #TH9044 you would need the part #908-1240-54. I confirmed this with Thule. This would be the same if you need to replace the same bolt for the combo #TH9044-TH9046.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...