Fishwire Tips and Spacer Block Orientation to Install Curt Trailer Hitch on a 2013 Chevy Equinox

Question

Question:

I have finally cleaned the threads out and can now install the hitch. The installation paper said to put a kink in the wire near the metal plates to prevent them from interfering with the carriage bolts. Do you have an example of that? Also is there a particular way the metal plates need to go in the frame as they are not symmetrical. I could not tell from the video as they do it so fast. Any pointers to make that part of the installation go easy? The plates look like they barely fit in the frame rail long ways but if you turn them sideways, they will fit better. Thanks

asked by: Brian W

0

Expert Reply:

By kinking the wire it just means you will bend it somewhere between the bolt and the spacer so that when you pull the bolt through it doesn't get stuck inside the frame from being bound up with the block.

The blocks do not go in the frame any certain way. Once you start to tighten them the block will turn as well until it hits the side of the frame allowing you to tighten the bolt without it spinning.

I have actually linked you 3 videos showing installation of Curt hitch # 13591. They are not all 2013 Chevy Equinox models but the installation is the same on all of them.

expert reply by: Michael H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 4

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 5

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 11

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 12

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...