What Center Cap Fits Kenda 5.70-8 Bias Trailer Tire with 8-inch Galvanized Wheel AM30130

Question

Question:

what size center hub will fit this wheel, I ordered last year and have never installed them.

asked by: Johnnie

0

Expert Reply:

The Kenda 5.70-8 Bias Trailer Tire with 8-inch Galvanized Wheel, part # AM30130, has a pilot hole diameter of 2.5-inches.

expert reply by: Adam R

0

Answer 1

To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel…

view full answer...

Answer 2

The first thing to try to is add some penetrating oil like WD40 and let it sit for awhile. You can then try tapping the bearing to try and remove it. You don't want to hit it too hard because you can damage the spindle. It is possible that…

view full answer...

Answer 3

If the hub that was on your trailer axle previously had 8-91A stamped on the back of it your spindle should require inner and outer bearings of #L44649 like you used. The part #8-91-05UC1 SHOULD be an exact replacement. However we need to double…

view full answer...

Answer 4

We don't offer replacement torsion beam axles, but we do offer the Timbren Axle-Less suspension that typically doesn't require an axle beam and won't require leaf springs, which could be a good solution for you. My research indicates that…

view full answer...

Answer 5

For your 2012 Ram 2500, you are correct that either suspension enhancement system will work. However there are major differences between them functionally. The Timbren system #TDR2500CA is a very solid jounce spring. It is a strong Aeon hollow rubber…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 9

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

What Center Cap Fits Kenda 5.70-8 Bias Trailer Tire with 8-inch Galvanized Wheel AM30130

Product Page this Question was Asked From

Continue Researching