Replacement Dexter Hub for 8-91A Hub
Question:
I have a boat trailer that has Dexter 8 - 91A hubs on it. The bearings are both L44649s and the grease seal has a 1.25 I.D with a 1.9 O.D. I do not see this combination on your site. Would it be possible to get this set up? Thank you for your time.
asked by: Gordon B
Expert Reply:
If the hub that was on your trailer axle previously had 8-91A stamped on the back of it your spindle should require inner and outer bearings of # L44649 like you used. The part # 8-91-05UC1 SHOULD be an exact replacement.
However we need to double check your grease seal measurement. Double check to make sure you don't have a 1.5 inner diameter seal with outer diameter of 1.9. You can also measure the spindle where the seal rides as well.
The seal dimensions you mentioned are not ones that are standard which means most likely you don't have them.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Trailer Hubs and Drums
- Hub
- Standard
- L44649
- L44649
- For 2000 lbs Axles
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Continue Researching
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb E-Z Lube Axles - 4 on 4 - L44649 Bearings
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Search Results: 8 91a hub
- Q&A: Replacement Bearings and Seals for a Dexter Hub with 8-91A Stamped on Back
- Video: Dexter Axle Trailer Hubs and Drums - Hub - 8-91-05UC1-EZ Review
- Shop: Bearing Kit, L44649 Inner/Outer Bearings, 10-9 Seal
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Search Results: 8~91a
- Shop: Trailer Wiring
- Search Results: dexter hub
- Search Results: cotter pin
- Search Results: dexter 8 91a
- Shop: Suspension Enhancement
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Search Results: bearing buddy 1.980
- Search Results: 20.5 8.0 10 tire
- Video: CE Smith Boat Trailer Parts - Roller and Bunk Parts - CE10052-32G Review
- Video: Americana Tires and Wheels - Wheel Only - AM20041 Review
- Q&A: Recommended Replacement Hub for Dexter 8-91A
- Q&A: Removing Trailer Bearing that is Stuck on Spindle After Removing Hub
- Shop: Roof Rack
- Q&A: Replacement Bearing Kit for Pop-Up Camper
- Q&A: Tire Size Upgrade from 4.80-12 on Trailer
- Q&A: Removing and Replacing Trailer Spindles
- Video: TruRyde Trailer Bearings and Races Kit Installation
- Video: Curt 4-Pole Flat Trailer Connector Mounting Bracket Review
- Q&A: Needing Dexter Hub # 8-91A
Bob D.
6/2/2020
I have a 1986 Starcraft Starlite 17 pop up that I am looking to replace the hub assemblies on. Dexter hub #8-91A. 4" bolt pattern, 1.500" & 1.062" diameter spindle, front & rear bearing # L 44549. Hub height 4.125", grease seal National 474476. Would this assembly be a direct replacement?