Removing Trailer Bearing that is Stuck on Spindle After Removing Hub
Question:
I have an old 6foot sears tent trailer with 8inch wheels 4 lug . question when I pull the hub off I cannot remove the inner bearing off the spindle. it popped off the hub with the grease seal and is still on the spindle ? This is the first time I have ever tried this job. Did not want to damage it with force .hammer At almost 70 years I am still trying to learn
asked by: Jim
Expert Reply:
The first thing to try to is add some penetrating oil like WD40 and let it sit for awhile. You can then try tapping the bearing to try and remove it. You don't want to hit it too hard because you can damage the spindle.
It is possible that the bearing has become welded to the spindle. This happens if there isn't enough grease and it gets too hot. If this is your problem the bearing and spindle are both bad, in which case it is recommended to replace the spindle or axle.
Product Page this Question was Asked From
Replacement Trailer Hub Bearing - 02475
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.250 Inch I.D.
- Bearing 02475
- Race 02420
- 8000 lbs Axle
- etrailer
more information >
Continue Researching
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Article: Most Popular Wheel Bearings
- Shop: Kenda Karrier S-Trail ST145/R12 Radial Tire w/ 12" Galvanized Spoke Wheel - 5 on 4-1/2 - LR D
- Video: etrailer Trailer Brakes AKBRKR-S-10 Review
- Video: Review of Westlake Tires and Wheels - Off Road Tire Only - WST54FR
- Shop: 7" x 1-3/4" Hydraulic Brake Shoe/Lining (One Wheel) - Dexter
- Shop: Westlake ST235/75R15 Radial Off-Road Trailer Tire - Load Range D
- Q&A: RV Step Recommendation that Can Fit 27 inch Wide Mounting Brackets
- Shop: Lippert Manual Pull-Out Step for RVs - Single - 6" Drop - 24-1/4" Wide - Steel - 300 lbs
- Shop: Flexco Manual Pull-Out Step for RVs - Single - 3" Drop/Rise - 24" Wide - 300 lbs
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: Torque Specification for 12 Inch Wheel with 4 Lug Nuts on Boat Trailer
- Q&A: How to Tell if a Trailer Spindle is Damaged or Needs to be Replaced
- Q&A: How to Determine Replacement Trailer Wheel Bearing Sizes
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-G-1K Review
- Q&A: Does a Spindle with Scarring and Complete Bearing Failure Need to be Replaced
- Q&A: How to Determine Inner and Outer Bearings on Trailer
- Article: Trailer Tire Sizing
- Search Results: spindle
- Search Results: calkins boat trailer
- Q&A: Will Upgrading from 8 Inch Wheel to 12 Inch Wheel Help Highway Performance
- Search Results: spindle nut
- Search Results: bearing buddy
- Article: Slipper Spring Trailer Suspension System Review
- Search Results: oil bath
- Shop: Suspension Enhancement
- Search Results: brake shoes
- Search Results: castle nut
- Video: etrailer Trailer Idler Hub Assembly Review AKIHUB-440-2-1K