Removing and Replacing Trailer Spindles
Question:
I have a question about spindles , I know how to replace hubs on my pontoon trailer. But how do I change the spindles. Do they bolt on or have to be welded to axle. Thanks
asked by: Tiny G
Expert Reply:
To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel tracking problems. I would recommend finding a welder who is experienced with trailer axles. Your local RV dealer or repair facility could probably refer you.
In many cases, it's less expensive to simply replace the trailer axle itself. We offer a basic selection of replacement 2000 and 3500 lb axles. If you'd care to reply with the following information, I'd be happy to make a recommendation for a replacement axle. I'll need to know the reference numbers off the inner and outer wheel bearings as well as the hub face to hub face dimension and the distance between the spring seats, measured center hole to center hole. I'll provide some diagrams showing how to get these measurements.
Product Page this Question was Asked From
Square #84 Spindle for 3,500-lb Trailer Axles - 1-1/2" Wide
- Trailer Spindles
- Standard Spindle
- 1-1/2 Inch Diameter
- Square
- For 3500 lb Axle
- TruRyde
more information >
Continue Researching
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Shop: #42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles - 2-1/4" Diameter
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Square #84 Spindle for 3,500-lb Trailer Axles - 1-1/2" Wide
- Shop: Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles - 89" Long - 3,500 lbs
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles - 4" Drop
- Q&A: How to Tell if a Trailer Spindle is Damaged or Needs to be Replaced
- Shop: Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility
- Video: Review of TruRyde Trailer Spindles - Replacement 42 EZ Lube Spindle - TRU37FR
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Search Results: trailer drop axle
- Shop: Gooseneck Hitch
- Q&A: Replacement For A Truryde RVD-H-65535 Hub
- Shop: Brake Controller
- Search Results: spring seat
- Video: Review of TruRyde Trailer Spindles - Standard Spindle - TRU47FR
- Search Results: spindle
- Video: Review of CURT Fifth Wheel Installation Kit - Custom Fifth Wheel Brackets - C16418
- Q&A: Hole Dimensions of Demco Channel Tongue Trailer Coupler # DM16080-95
- Video: Review of Demco Straight Tongue Trailer Coupler - Standard Coupler - DM16080-95
- Video: TruRyde Electric Trailer Brake Kit Installation
- Shop: Suspension Enhancement
- Q&A: What is the Hole Spacing for Mounting etrailer 10 Inch Hydraulic Trailer Brake # AKUBRK-35L-D
- Q&A: Mounting Bolt Spacing and Center Hole Size for etrailer 10 Inch Hydraulic Trailer Brake Assembly
- Video: Trailer Hub Inspection Demonstration
- Video: Bearing Repacking and Grease Seals Installation
- Search Results: 5 on 5 axle
- Q&A: How To Remove Spindles From Trailer Axle
- Search Results: trailer brakes
- Search Results: electric brake magnet clip
Jesse
8/10/2020
Hi! Thank you very much for the feedback, had a quick question for you. Do you know if a machine exists to put together a spindle and an axle? Thanks!