Material of Replacement Washer 853-2154

Question

Question:

What is the material of this Rectangular washer with the 1/4inch square hole? Is it Zinc Coated, Stainless Steel, or Galvanized coated steel.

asked by: Dan

0

Expert Reply:

I spoke to my contact at Thule and the washer you mentioned # 853-2154 is made out of steel with a zinc plating.

expert reply by: Jackie C

0

Answer 1

I do have a solution for you, however the closest spacer block we currently have available to the dimensions you listed in your question is the Reese Spacer Block #RP3022. The size of this spacer block is 1/4" x 1" x 3". If you are…

view full answer...

Answer 2

Did two of the weldnuts in your trailer frame brake as you were tightening them down? All 6 of the install bolts for the Draw Tite hitch part #75270 will thread into the weldnuts on the vehicle frame. Broken weldnuts can be rather annoying when…

view full answer...

Answer 3

The weld nuts were probably still dirty, when you were installing the hitch which caused the weld nut to brake off when putting torque on it. If you have not already installed the other bolts, you will want to clean them out with WD-40 and wire brush…

view full answer...

Answer 4

The EZ Haul Car Tow Dolly with hydraulic brakes looks like a pretty straight-forward tow dolly that has entry-level quality that get's the job done. We don't carry this tow dolly so I can't speak to longevity but for what it is it seems…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Material of Replacement Washer 853-2154

Product Page this Question was Asked From

Continue Researching