Customers compare 80101-1 to these similar products
Products Featured in this Video
All right today, we're going to demonstrate part number 80101-1. This is a half inch bolt leader. Now this part is typically used to install carriage bolts and blocks inside the frame of the vehicle for attachment points for a hitch. We got our hardware here, a typical half inch carriage bolt and a block. We'll go ahead and put those together and then take a bolt leader, also known as a wire pull… see more >
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The Curt Trailer Hitch Receiver item #C74DR fits both the Rubicon and standard or excluding Rubicon 2023 Jeep Gladiators. Our fitguide can be confusing when it comes to model break downs and this is another example of that. The Curt Trailer Hitch…
view full answer...If you are just looking to tow a trailer with lights and without brakes, I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part #C56349. This will give you a 4-Pole flat on the back of the Tacoma to tow a…
view full answer...The best overall option for adding a Curt trailer hitch receiver to your 2023 Jeep Gladiator is the one that gives you the most overall function and capacity, which is the hitch that bolts onto your frame: - Curt Trailer Hitch Receiver #C74DR There…
view full answer...I can help you outfit your 2016 Ram 3500 with a complete Torklift setup. First thing you will need for your 8 foot bed with factory hitch, is the Torklift hitch #TLD1108, this will give you a second 2 inch receiver on your truck and will allow you to…
view full answer...Of the two part numbers you mentioned only the #TLF2022A is a fit for your 2022 Ford F-350 short bed without factory board and with the factory installed hitch. You might have meant to type #TLF2022 which is the non-aluminum/stainless steel option…
view full answer...The correct Torklift camper tie downs you need for your 2017 Ram 3500 dually without steps and a factory hitch is the part numbers #TLD2124 and #TLD3109 for steel or if you prefer aluminum which will be more corrosion resistant as part numbers…
view full answer...You'd be able to reuse the rear tied downs part #TLD3109 on your 2017 Ram 3500, but you'd have to go with the new part #TLD2124 for the front as what was on your old truck will not transfer.
view full answer...I have some great frame mounted camper tie down options for a 2017 Ram 3500 but there are several options depending on bed size, cab type, step option, hitch option, etc. so I would need more information on the vehicle to be able to confirm fit. For…
view full answer...The camper tie-downs that are designed to fit your 2017 Ram 3500 that I recommend are part #TLD2124 for the front and part #TLR3507 for the rear. These are specifically designed for a 2017 3500 Crew Cab With no running boards or steps and with an…
view full answer...If you purchase the TorkLift SuperHitch Magnum Trailer Hitch Receiver - Custom Fit - Class V - 2" #TLD1108-30 for your 2018 Ram 3500 you will need to replace the rear TorkLift tie downs on your truck. You will need the TorkLift Custom…
view full answer...The weight is pretty similar between the aluminum Torklift camper tie downs part #TLF2022A and the steel part #TLF2022 which is 4 lbs heavier at 39 lbs vs 43 lbs.
view full answer...I was able to reach out to my tech contact over at TorkLift to get some guidance on the installation of the TorkLift Front Tie-Down #TLF2022 for you. He mentioned that you'll want to apply pressure to the tie-down (pull it down a little bit) or…
view full answer...