Troubleshooting Trailer Braking System With Brake Controller Indicating OL or Overload Error Code
Question:
2005 Chevy Colorado, everything wired in as best I could. I got infrequent overloadfoot messages on my controller, the TK90160. It happens when the trailer is loaded and unloaded. Just what does the overload mean? With an empty trailer, Im WELL under the 4000lb rating.
asked by: Robert S
Expert Reply:
The OL or overload error code indicates a short in the brake output circuit. As a first step, you will want to see if the problem exists with the wiring on the trailer or on the vehicle. Due to its intermittent nature, I'm suspecting a loose connection or a worn wire in the brake controller's output circuit.
Try unplugging the trailer and activating the manual brake switch on the controller. If you get the error code at that point, it is a pretty good indication that the problem exists on the output circuit between the brake controller and the trailer connector. First, check the connector itself. Make sure it is not damaged or corroded. If you can see white or green corrosion on the trailer connector's pins, there is a good possibility that the corrosion has migrated to the interior of the connector. If you can access the rear of the connector where the wires attach to the terminals, check those for corrosion and repair or replace if necessary.
If all appears well with the trailer connector, sever the blue wire a few inches behind the controller (leaving enough room to reconnect it later). Try the manual switch again. If the error code has disappeared, then the short is in the wire between the controller and the trailer connector. Simply run a new length of # 10-1-1 from the controller to the trailer connector, bypassing the wire that has the short.
If the OL code only occurs when the trailer is connected, then the problem lies with the wiring on the trailer. Check the trailer connector for damage or corrosion. Trace the brake output circuit (usually a blue wire) from the trailer connector back to the brake assemblies looking for broken or pinched wires or loose connections. Examine the wire insulation, looking for worn or cracked spots that would allow the copper conductor to contact the trailer frame or other metal. Make sure that one lead from each magnet ties into the brake output wire, and the other grounds to the trailer frame. If all this checks out OK, your magnets might be worn. Pull off one of your hubs, and examine the face of the magnet that rides against the inside of the brake drum. If you can see any of the interior copper wiring encased in the magnet, the magnet is worn to the point of being unserviceable and should be replaced.
I have linked you to a brake magnet and brake controller troubleshooting FAQ article that you might find helpful.
Products Referenced in This Question
Product Page this Question was Asked From
Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 3 Axles
- LED Display
- Up to 90 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: etrailer Electric Trailer Brakes Installation - 2019 Grand Design Reflection 150 Fifth Wheel
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Shop: Brake Controller
- Q&A: Diagnosing Overload Warning, No Brakes, On a Tekonsha Prodigy P3 Brake Controller
- Shop: Electric Trailer Brake Assembly - 12" - Left Hand - 5,200 lbs to 7,000 lbs
- Q&A: Correct Replacement for AXLETEK-12-GG Trailer Brakes
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 12" - 8 on 6-1/2
- Shop: Easy Grease Trailer Hub and Drum for 5.2K to 7K Axles - 12" - 8 on 6-1/2 - Galvanized
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7K
- Shop: Dexter Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7,000 lbs
- Shop: TruRyde Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand Assemblies - 7K
- Video: etrailer Electric Trailer Brakes Installation on a 2017 Grand Design Reflection Fifth Wheel
- Article: Testing Trailer Brake Magnets for Proper Function
- Shop: Performance Chip Tuners
- Q&A: Can 91 Octane Tune of Superchips Programmer be Used for Daily Driver
- Search Results: bulldog jack
- Search Results: breakaway kit
- Search Results: jacks and jack stands
- Q&A: What Does an Intermittent Flashing OL Code Mean for a Brake Controller
- Q&A: Troubleshooting Curt Echo Brake Controller Showing Electrical Overload
- Q&A: Troubleshooting Curt Echo Signaling "Overload" Warning on 2015 Cadillac Escalade
- Shop: Trailer Hitch
- Q&A: Electric Trailer Brakes not Working
- Video: Trailer Brake Controller Installation - 2015 Chevrolet Tahoe 90195
- Search Results: recurve r3
- Article: Best Air Bag Suspension (2023)
- Article: How to Install a Weight Distribution Hitch (With Pictures & Video)
- Shop: Trailer Wiring
- Article: Troubleshooting Brake Controller Installations
- Search Results: trailer door locks
on Trailer Brake Controller
