Dimensions of Stromberg Carlson Electric Trailer Jack JET-5000

Question

Question:

What is the mounting bolt hole spacing? I have a three hole mount and the bolts are 3inch apart.

asked by: Tom R

0

Expert Reply:

I've got great news for you, the mounting holes on the Stromberg Carlson Electric Trailer Jack # JET-5000 are 3 inches apart. A-frame jacks have an industry standard dimension because of the style of coupler used on A-frame trailers.

The measurement you will want to make sure fits is the outer tubing diameter of the jack's leg. For the Brute, that tubing diameter is 2-3/16 inches.

I linked a Help article on jacks for your convenience.

expert reply by: Jackie C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Your typical electric jack is designed to fit an A-frame so the only one we carry that is a side mount is the Fulton XLT #F141401. However, you may be interested in the Trailer Valet JXS Drill Powered Swivel Trailer Jack #TV64FR. This jack has a hand…

view full answer...

Answer 10

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 11

Hi Tom, I have two options to replace the electric tongue jack on your Jayco Whitehawk: Option 1: Electric Jack w/ Footplate #EJ-3520-BBX. This jack is going to be your no-frills 'get the job done' style jack. It has a 3,500lb capacity and…

view full answer...

Answer 12

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...