Troubleshooting Flashing PL Code on Tekonsha Primus Brake Controller

Question

Question:

It is constantly flashing PL

asked by: Jimmyshehee

0

Expert Reply:

The PL error code on the Primus brake controller # TK90160 indicates that power is interrupted when stepping on the brake pedal. Check the connection of the red wire. It should be attached to the brake switch wire that has power only when the brake pedal is pressed. If it has power at any other time then it is not the correct wire.

I have also included some links to testing and troubleshooting brake controllers that should also help.

expert reply by: Jameson C

0

Answer 1

The brake light circuit actually differs from the brake controller circuit. If you check out the linked photo you can see that the brake/stop light circuit is actually tied to the left and right turn circuits as well which as in the 3 and 9…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...