Roadmaster Crossbar-Style Base Plate Kit - Removable Arms

etrailer service is and has always been stellar. My order was correct and was delivered very quickly. The only reason I made this a four instead of a five was that the rear bolt position of both base plate brackets where welded on crooked. Each small plate was at a different angle from each other. In my opinion whoever welded them wasn’t paying attention to quality control. Because I was on a time crunch for my departure on a trip and could not wait for replacements (and I needed the vehicle for local driving) I made the brackets work. Other than that the installation went smoothly and I was able to test tow my 2004 CRV a couple of times without incident.1516071

Very impressed that they're the exact fabbed fit, and easy to install! These tow base plates are super sturdy!1731536

Click to Enlarge

Item arrived earlier than predicted after viewing a very complete tracking system. The information was very clear and precise. Good job! I am 75 years of age and installed the baseplate myself. Only a couple of minor issues. One pin would not insert. Welding blob in the way. Filed it smooth and problem solved. The video was excellent but was a bit different in that it showed a different method o rear bolt installation, however the instructions on paper showed the correct way. Reinstalling the front clip had presented some difficulty. I suggest really watching the inner fender position relative to the front clip before removal. All said all went well. The finished look is great, (see pictures). Great product!1230787

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

by: Brian 05/08/2024

Just completed a 6600 mile rod trip, towing the Subaru behind a motor home.

Worked great.2002307

by: Barney04/06/2024

I've towed with it many times and Zero problems. I did find that moving the car slightly forward after stopping helps relax tension amd.make.disconnect much easier. Overall... I'd say SUPER..!!1760607

by: William 05/04/2024

It was easy to install, fit well and came with good instructions.1779256

Base plate 1910 install on 1999 Landrover disco 2

the base plate arrived fast (as does everything I have ordered from etrailer). It was a bit bent on arrival but Becky sorted me out and offered to replace it but it was easy to bend back (with a 3lb hammer).

The included instructions were great for removing the bumper but nor much else. Possibly because my Landy is a 1999 disco 2 and the pictures were of a 2002.

I have included some pictures of stuff I wish I had known. Firstly I had to loose the recovery loop on the driver side as the base plate would not fit over it. The chassis frame has steel tubes inside the bolt holes so the amount of drilling is minimal (I ordered a drill bit that they suggested but in all honesty could have opened up the holes with a file easily).

You need to oval out the aluminum crush cans before you replce them or the new bolts will not go through. The center mount bolt just needs the plastic mount for the center screw on the scoop cut out and there is a bog square hole on the top of the member (thats why you need to big square piece of steel on the top of the center bolt)

Mine was obscured by the torsion bar so I ended up dropping it to drill out the hole and get the bolt in straight.

It was easy to bolt up to the frame once everything was prepped and do yourself a favour and buy loctite red for the bolts - you don't want to be going in there again.

The bumper template was a good start but I had to reshape mine a lot particularly as the hole on the baseplate ended up halfway through the bumper and I had to do a lot of enlargement at the bottom to attach the safety wires.

The photos should make more sense of some of my description1210129

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Everything looks good for us, but we have one more part that we are waiting on before we can install on the truck plus it's raining out here in Washington State. when it's time to put it all together we will take a picture and send it.1495552

The baseplate and crossbar arrived one day earlier than expected. Directions were included which made the installation pretty easy.
I am happy with etrailers products and will buy from them again.1724154

by: Greg 05/05/2023

Very easy to install and works great 1571352

by: J.C. Randall07/23/2018

This base plate was installed on a 2008 Kia Spectra. The bracket is strong and not really hard to work with HOWEVER,,,,,,,,,, I am used to the BlueOx base plate which is much easier to "hook up". Unfortunately, BlueOx did not make a base plate to fit my vehicle. That is not a big problem as I'm usually not in any hurry and it only takes maybe 5 minutes longer to "hook up".

The biggest problem with the RoadMaster base plate is that due to the way it is bolted to the frame, it only allows for a 6-inch ground clearance on the front of the vehicle. I have to be very careful with any "dips" in the road, especially on cross streets. Six inches may not sound like much but since the tires are several feet behind the base plate, it reduces that ground clearance greatly. It also will not clear the concrete "stop blocks" in front of many parking spaces.

If you are not very careful and keep this in mind, you may likely bend the frame of your car when you come to one of these sudden impacts. I haven't bent anything yet but it has certainly been shocking when it hits. Most of the time, the impact will cause the base plate to scrape and lift the car to the height to clear the obstacle.

I've attached a picture with a ruler in the view.545124

Click to Enlarge

The hardest part of the installation is getting the grill off and back on. Of the six preexisting holes all but one lined up the sixth hole was off about a half inch but the car had hit a deer a few years ago.1549576

Click to Enlarge

Good information and prompt shipping.
Base plate is solid and install and use instructions are excellent.
Be warned that product install is drill two holes and install 3 bolts, BUT the entire front panel has to be removed and replaced. Not difficult, but time-consuming.
Seat bracket is solid and install and use instructions are excellent.
Brakemaster kit is good quality, but instructions are not as good as most Roadmaster products. Instructions for air line install are especially weak.167660

Click to Enlarge

Click to Enlarge

My husband and I were able to install the Roadmaster base plates on our 92 Jeep Cherokee in just a couple of hours. It went on pretty much the same as the demonstration video on the etrailer web site. The minor differences were addressed in the printed instructions that were included in our package. We haven't put it to the test yet as we still need to tackle wiring for the Roadmaster Even brake system that we purchased second hand. We will be towing our Jeep with our 93 Safari Trek. Customer service provided by Marty was excellent. I will provide pictures at a later date.1685211

by: Rifleman04/11/2019

Installed on a 2010 Ford Ranger Sport 2wd
Have towed over 10000 and not one issue. I did the install without one issue, picture perfect, I did use a online video to get a general idea of install otherwise I primarily used manufacturer's. . Be sure to use the recommended/ required locktite product.
Enjoy!!!621575

Click to Enlarge

Click to Enlarge

This was a very simple install. This is my 4th baseplate I have bought and 2 pintle tow bars. Always excellent craftsmanship1688902

Base plate kit was fairly easy to install,all hardware was included and directions were clear! I would definitely buy another to install if ever needed. I do have a car lift making it easier,but would not be bad without,just a little harder on the knees!647182

Click to Enlarge

by: Pablo 10/18/2022

Great product and easy to use . Car tows great behind the motor home.1451110

Great product, shipping was FAST. Instructions were adequate, but minimum - this was not surprising, you have to know how to bend wrenches to install something like this yourself.
I had a factory-installed tow hook on each side that had to be uninstalled, but once you remove the front bumper shroud it is easy to remove and all the bolts are easy to remove. Once the hook was out of the way, easy-peasy!729492

Click to Enlarge

by: Demingo04/22/2024

Highly recommend E-Trailer for all of your towing accessories. Great product, great customer service!!1771296

Super nice people at etrailer. I wasn’t sure exactly what I needed and they helped me pick out the best hitch for me.1189955

Click to Enlarge

by: MEC02/22/2021

Very rugged kit with excellent instructions. A DIYer with medium mechanical skills can install. Involved removing the front bumper which was not difficult. Value for the price is very good. As always, etrailer support was also very good.964073

Click to Enlarge

by: Robert 03/24/2024

I had to ream out one of the holes to fit my 95 Tahoe. No problem hooking up after that. Went right in with no other modifications and no problems. Have towed a few thousand miles now and they worked great for me.1753238

What a job to install this thing! Does not line up with any of the existing holes. It is close, but still a real bear to get into place. Instructions do not have any photos. The instructions also list bolts that are not in the kit. I strike that up to a misprint, but still very confusing. It requires a drill bit, that I could not find any any hardware store or auto store. 17/32 drill bit? Maybe include that with the parts? Definitely helps to have another hand and a lot of patience. No videos online about this install and what to do about all the gaps where it does not properly line up at the right angle for towing.1678713

Great product,installation took about 3 hours,instructions were good,go step by step.works well with the roadmaster falcon tow bar.600529

Click to Enlarge

Click to Enlarge